Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057113  Brake Switch "A" Circuit Open  


DESCRIPTION

When the brakes are applied by the dynamic radar cruise control system, the skid control ECU (brake booster with master cylinder assembly) operates the stop light switch assembly (stop light relay) to illuminate the stop lights.

If the hybrid vehicle control ECU receives a stop light switch control relay malfunction signal from the skid control ECU (brake booster with master cylinder assembly), DTC P057113 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057113 Brake Switch "A" Circuit Open
w/o Full-speed range following function:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU receives a stop light switch control relay malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 0.5 seconds or more.


w/ Full-speed range following function:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU receives a stop light switch control relay malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 0.5 seconds or more.


·

Pre-crash safety system

·

Stop light switch assembly

·

Skid control ECU (brake booster with master cylinder assembly)

·

Hybrid vehicle control ECU

·

Harness or connector



WIRING DIAGRAM

B429078E04
5.042,0.417 6.365,0.635 1.323,0.219 10 false from J/B-B Fuse 5.042,1.219 6.479,1.427 1.438,0.208 10 false from IG2-NO. 2 Relay 3.51,0.552 4.125,0.75 0.615,0.198 10 false STOP 3.292,1.365 5.281,1.563 1.99,0.198 10 false ECU-IG2 NO. 3 2.625,0.313 2.781,0.51 0.156,0.198 10 false B 2.615,1.115 2.771,1.313 0.156,0.198 10 false B 5.292,4 5.75,4.198 0.458,0.198 10 false STP 5.281,3.396 5.74,3.594 0.458,0.198 10 false STPO 5.281,2.438 5.74,2.635 0.458,0.198 10 false STP2 2.625,2.458 2.781,2.656 0.156,0.198 10 false L 2.438,3.396 2.896,3.594 0.458,0.198 10 false ACC 2.438,4.031 2.896,4.229 0.458,0.198 10 false OUT 0.823,4.042 1.281,4.24 0.458,0.198 10 false GND 0.896,4.646 2.667,4.854 1.771,0.208 10 false Stop Light Switch Assembly 2.385,5.208 4.375,5.406 1.99,0.198 10 false to Stop lights 4.813,4.938 7.073,5.302 2.26,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.906,4.5 1.365,4.698 0.458,0.198 10 false A47 4.833,4.781 5.292,4.979 0.458,0.198 10 false A41 5.042,2.438 5.354,2.635 0.313,0.198 10 false 37 5.052,4 5.365,4.198 0.313,0.198 10 false 12 5.052,3.385 5.302,3.583 0.25,0.198 10 false 22 2.802,2.458 2.958,2.656 0.156,0.198 10 false 3 2.802,3.396 2.958,3.594 0.156,0.198 10 false 4 2.792,4.021 2.948,4.219 0.156,0.198 10 false 1 2.802,0.313 2.958,0.51 0.156,0.198 10 false 7 2.802,1.115 2.958,1.313 0.156,0.198 10 false 6 0.677,4.042 0.833,4.24 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
HINT:

When DTC P057113 is stored by the dynamic radar cruise control system, DTC C1A4B is stored by the pre-crash safety system. Therefore, if DTC P057113 is stored, inspect the pre-crash safety system first.



Result:
Result Proceed to
Pre-crash safety system DTCs are not output A
Pre-crash safety system DTCs are output B



A

2.CHECK STOP LIGHT OPERATION

B

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:

The stop lights illuminate when the brake pedal is depressed. The stop lights turn off when the brake pedal is released.



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY OUTPUT)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY OUTPUT)
a.

According to the display on the GTS, perform the Active Test Stop Light Relay.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop lights ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Stop Light Relay
Data List Display
Stop Light Relay Output
50004 105 5 291

b.

According to the display on the GTS, perform the Data List Stop Light Relay.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output STPO terminal output condition ON or OFF ON: Output
OFF: Not output
-

c.

Check that the Data List item Stop Light Relay Output changes between ON and OFF and the stop lights turn on and off according to the operation of the Active Test.


Result:
Result Proceed to
The Data List item Stop Light Relay Output changes between ON and OFF and the stop lights operate as normal A
The Data List item Stop Light Relay Output does not change between ON and OFF or the stop lights do not operate as normal B



A

5.CHECK FOR DTC (RADAR CRUISE 1)

B

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
5.CHECK FOR DTC (RADAR CRUISE 1)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 399

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.

w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399

Result:
Result Proceed to
DTC P057113 is not output A
DTC P057113 is output B



A

B

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-1 (OUT) - A41-12 (STP) Always Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition
A47-4 (ACC) - A41-22 (STPO) Always Below 1 Ω
A47-4 (ACC) or A41-22 (STPO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR