Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047527 CRUISE CONTROL _0244900 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives the signal, it cancels control of vehicle speed by the dynamic radar cruise control system. The fail-safe function operates to enable normal operation even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the hybrid vehicle control ECU through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU turns the dynamic radar cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure
w/o Full-speed range following function:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.


w/ Full-speed range following function:
·

While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.


·

Stop light switch assembly

·

Harness or connector

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A375977E02
2.406,0.646 3.021,0.844 0.615,0.198 10 false STOP 2.177,1.177 4.01,1.375 1.833,0.198 10 false ECU-IG2 NO. 3 3.146,2.01 5.438,2.208 2.292,0.198 10 false Stop Light Switch Assembly 0.406,0.51 2.094,0.708 1.688,0.198 10 false from J/B-B Fuse 0.104,0.99 2.094,1.188 1.99,0.198 10 false from IG2-NO. 2 Relay 3.563,0.51 3.719,0.708 0.156,0.198 10 false B 3.563,1.01 3.719,1.208 0.156,0.198 10 false B 3.563,1.521 4.021,1.719 0.458,0.198 10 false GND 4.177,1.177 4.333,1.375 0.156,0.198 10 false L 4.167,0.396 4.323,0.594 0.156,0.198 10 false L 5.677,0.292 6.135,0.49 0.458,0.198 10 false STP 5.677,1.083 6.135,1.281 0.458,0.198 10 false ST1- 3.906,2.719 4.365,2.917 0.458,0.198 10 false STP2 5.74,2.708 6.198,2.906 0.458,0.198 10 false STP1 5.375,1.885 7.104,2.094 1.729,0.208 10 false Hybrid Vehicle Control ECU 5.365,3.083 6.896,3.438 1.531,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.365,2.938 5.823,3.135 0.458,0.198 10 false M59 3.156,1.875 3.615,2.073 0.458,0.198 10 false A47 5.313,0.385 5.771,0.583 0.458,0.198 10 false A50 2.729,2.927 3.188,3.125 0.458,0.198 10 false A41 3.406,0.917 3.563,1.115 0.156,0.198 10 false 6 3.406,0.417 3.563,0.615 0.156,0.198 10 false 7 3.406,1.417 3.563,1.615 0.156,0.198 10 false 2 4.333,0.302 4.49,0.5 0.156,0.198 10 false 3 4.333,1.083 4.49,1.281 0.156,0.198 10 false 5 5.344,1.188 5.656,1.385 0.313,0.198 10 false F2 5.375,0.167 5.531,0.365 0.156,0.198 10 false 7 5.333,0.979 5.646,1.177 0.313,0.198 10 false 28 4.344,2.615 4.656,2.813 0.313,0.198 10 false 37 5.51,2.615 5.823,2.813 0.313,0.198 10 false 25 2.719,3.083 5.042,3.458 2.323,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E233306C50
1.521,0.26 1.854,0.479 0.333,0.219 1.292,1.167 1.042,1.854 true 2.281,1.115 2.656,0.958 true 1.958,1.177 1.708,1.865 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.573,0.302 2,0.521 0.427,0.219 10 false A47 2.708,0.875 2.875,1.042 0.167,0.167 10 false B 0.906,1.896 1.417,2.135 0.51,0.24 10 false GND 1.667,1.896 1.833,2.063 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A47 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A47-7 (B) - Body ground Always 11 to 14 V
A47-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A47-6 (B) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the stop light switch assembly connector.


c.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the certification ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-28 (ST1-) - A47-5 (L) Always Below 1 Ω
A50-7 (STP) - A47-3 (L) Always Below 1 Ω
F2-28 (ST1-) or A47-5 (L) - Body ground Always 10 kΩ or higher
A50-7 (STP) or A47-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR