Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › CYLINDER HEAD
RM3210E _51 Engine / Hybrid System _047495 2ZR-FXE ENGINE MECHANICAL _0244908 CYLINDER HEAD A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
for SFI system (w/ Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system (w/o Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) or frame number registration (Click here)
for SFI system (w/ Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
for SFI system (w/o Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple advanced parking guidance system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A374030C01
2.604,1.844 2.896,1.844 false 1.542,0.656 1.833,0.656 false 2.969,1.771 3.281,1.927 0.313,0.156 10 false *a 1.26,0.594 1.719,0.792 0.458,0.198 10 false SST
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 inner compression springs and 8 intake valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

a.
A374031C01
1.865,2.052 2.771,1.917 2.771,1.917 2.458,1.615 false 0.573,0.281 0.688,0.375 false 2.833,1.854 3.146,2.01 0.313,0.156 10 false *a 0.323,0.177 0.781,0.375 0.458,0.198 10 false SST
*a Wooden Block


Using SST and wooden blocks, compress the inner compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 inner compression springs and 8 exhaust valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 3.REMOVE VALVE STEM OIL SEAL

a.
A374032

Using needle-nose pliers, remove the 16 valve stem oil seals.


Hide 13734 4.REMOVE VALVE SPRING SEAT

a.
A374033

Using compressed air and a Magnet Hand, remove the 16 valve spring seats from the cylinder head sub-assembly by blowing air onto them.


Hide 11117B 5.REMOVE NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from the No. 2 straight screw plug or the No. 2 straight screw plug is corroded, replace it.


a.
A374034

Using a 10 mm straight hexagon wrench, remove the 3 No. 2 straight screw plugs and 3 gaskets from the cylinder head sub-assembly.