Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › SHIFT CONTROL ACTUATOR
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0244921 SHIFT CONTROL ACTUATOR A

P610 HYBRID TRANSMISSION / TRANSAXLE  SHIFT CONTROL ACTUATOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SHIFT CONTROL ACTUATOR ASSEMBLY

a.

Clean and degrease the bolt holes of the hybrid vehicle transaxle assembly.


b.
C353577C01
1.969,1.25 2.021,0.479 2.021,0.479 2.156,0.479 false 2.198,0.385 2.438,0.625 0.24,0.24 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of 2 new shift control actuator bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 2 shift control actuator bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.
C348454

Using a 12 mm hexagon socket wrench, temporarily install the shift control actuator assembly to the hybrid vehicle transaxle assembly with the 2 shift control actuator bolts.

NOTICE:

Do not tap the shift control actuator assembly with a plastic hammer or similar tool when installing it.


HINT:

As the position of the shift control actuator assembly is detected automatically, initialization is not necessary after disconnecting and reconnecting the cable to the negative (-) auxiliary battery terminal.



d.
A192239C79
1.823,1.198 1.865,0.427 1.865,0.427 1.979,0.427 false 2.01,0.365 2.333,0.542 0.323,0.177 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of a new shift control actuator bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the shift control actuator bolt immediately after applying adhesive to prevent foreign matter from attaching to it.



e.
C348455

Temporarily install the shift control actuator bolt.


f.
C348456

Using a 12 mm hexagon socket wrench, tighten the 2 shift control actuator bolts.

Torque:
16.5 N*m (168 kgf*cm, 12 ft.*lbf)


g.
C348455

Tighten the shift control actuator bolt.

Torque:
16.5 N*m (168 kgf*cm, 12 ft.*lbf)


h.
C353578C01
1.969,1.229 2.063,0.427 2.063,0.427 2.188,0.427 false 2.229,0.344 2.469,0.552 0.24,0.208 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of 2 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 2 bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



i.

Install the 2 bolts to the 2 shift control actuator bolts.

C349847C01
3.271,0.781 3.448,0.781 false 0.448,0.781 0.656,0.781 false 0.281,0.698 0.594,0.854 0.313,0.156 10 false *a 3.479,0.698 3.698,0.865 0.219,0.167 10 false *a
*a Bolt Head Breaking Position - -


NOTICE:

Tighten the bolts until the bolt heads break off.


HINT:

Breaking Torque: 4.9 to 8.8 N*m (50 to 90 kgf*cm, 43 to 78 in.*lbf)



j.

Connect the shift control actuator assembly connector.


Hide 51441 2.INSTALL NO. 1 ENGINE UNDER COVER