Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3210E _58 Vehicle Interior _047531 LIGHTING (INT) _0244928 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the power switch on (IG) or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E344235E05
0.604,0.729 2.021,1.146 1.417,0.417 10 false from Auxiliary Battery 0.125,1.24 1.938,1.708 1.813,0.469 10 false from Certification ECU (Smart Key ECU Assembly) 2.51,0.927 3.281,1.229 0.771,0.302 10 false J/B-AM 3.208,0.771 3.979,1.073 0.771,0.302 10 false 3K 3.26,0.563 4.031,0.865 0.771,0.302 10 false 1 3.219,1.063 3.99,1.365 0.771,0.302 10 false 17 3.219,1.25 3.99,1.552 0.771,0.302 10 false 3A 3.26,1.656 4.031,1.958 0.771,0.302 10 false 3 3.208,1.865 3.979,2.167 0.771,0.302 10 false 3D 3.479,2.406 6.219,2.708 2.74,0.302 10 false Instrument Panel Junction Block Assembly 4.052,1.542 4.823,1.844 0.771,0.302 10 false IG1 NO.1 4.75,0.938 5.771,1.25 1.021,0.313 10 false ECU-IG1 NO.4 5.885,0.771 6.656,1.073 0.771,0.302 10 false MB 5.917,0.573 6.688,0.875 0.771,0.302 10 false 32 6.281,0.656 7.052,0.958 0.771,0.302 10 false IG 6.281,1.865 7.052,2.167 0.771,0.302 10 false GND1 5.917,1.667 6.688,1.969 0.771,0.302 10 false 11 5.385,2.813 7.031,3.302 1.646,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 5.896,1.865 6.667,2.167 0.771,0.302 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC (ENTRY AND START SYSTEM (for Start Function))
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Clear DTCs
50002 223

b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
Entry and Start System (for Start Function) DTCs are not output A
Entry and Start System (for Start Function) DTCs are output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW Power switch on (IG) signal ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-
Body Electrical > Main Body > Data List
Tester Display
IG SW
50003 123 30
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3K-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E333577C06
1.698,0.51 2.042,0.729 0.344,0.219 4.938,0.531 5.281,0.75 0.344,0.219 2.438,2.438 2.781,2.656 0.344,0.219 5.729,2.292 6.073,2.51 0.344,0.219 4.219,3.115 4.396,3.396 false 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 1.802,0.542 2.219,0.781 0.417,0.24 10 false 3D 5.031,0.552 5.448,0.792 0.417,0.24 10 false 3A 2.521,2.469 2.938,2.708 0.417,0.24 10 false MB 5.823,2.323 6.24,2.563 0.417,0.24 10 false 3K 4.458,3.385 4.875,3.625 0.417,0.24 10 false IG
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3K-1 - MB-32 (IG) Auxiliary battery not connected to 3A-17 and 3D-3 10 kΩ or higher
3K-1 - MB-32 (IG) Auxiliary battery positive (+) → 3A-17
Auxiliary battery negative (-) → 3D-3
Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY