Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3210E _58 Vehicle Interior _047531 LIGHTING (INT) _0244928 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Auto Cut Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls operation of the DOME CUT relay in order to supply power to the interior lights. When the battery saving function operates while the interior lights are on, the main body ECU (multiplex network body ECU) opens the DOME CUT relay to turn off the lights.

WIRING DIAGRAM

E341747E03
0.219,0.563 1.646,0.948 1.427,0.385 10 false from Auxiliary Battery 0.177,1.875 1.49,2.188 1.313,0.313 10 false to Each Interior Light 2.396,0.385 2.99,0.677 0.594,0.292 10 false 1 2.365,0.583 2.958,0.875 0.594,0.292 10 false 3K 2.365,1.365 2.958,1.656 0.594,0.292 10 false 19 2.354,1.552 2.948,1.844 0.594,0.292 10 false 3H 2.396,1.979 2.99,2.271 0.594,0.292 10 false 9 2.354,2.177 2.948,2.469 0.594,0.292 10 false 3D 2.677,2.542 5.427,2.844 2.75,0.302 10 false Instrument Panel Junction Block Assembly 3.031,0.74 3.625,1.031 0.594,0.292 10 false DOME 5.271,0.583 5.865,0.875 0.594,0.292 10 false MB 5.292,0.385 5.865,0.688 0.573,0.302 10 false 23 5.625,0.469 6.219,0.76 0.594,0.292 10 false DOMR 5.271,2.948 6.927,3.469 1.656,0.521 10 false Main Body ECU (Multiplex Network Body ECU) 4.031,1.219 4.917,1.552 0.885,0.333 10 false DOME CUT

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF When performing this active test, turn all the interior lights on.
·

ON: DOME CUT relay off (interior lights turn off)

·

OFF: DOME CUT relay on (interior lights turn on)


Body Electrical > Main Body > Active Test
Tester Display
Relay for Interior Light Auto Cut Function
50004 123 66
OK:

All of the interior lights turn off when ON is selected.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3K-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the voltage and resistance according to the value(s) in the table below.

E333583C01
1.958,0.677 2.271,0.875 0.313,0.198 5.177,0.688 5.49,0.885 0.313,0.198 2.354,2.531 2.667,2.729 0.313,0.198 5.729,2.385 6.042,2.583 0.313,0.198 3.552,3.427 3.271,3.094 false 0.208,0.24 0.521,0.396 0.313,0.156 10 false *a 2.042,0.719 2.49,1.052 0.448,0.333 10 false 3H 5.24,0.719 5.688,1.052 0.448,0.333 10 false 3D 2.427,2.563 2.875,2.896 0.448,0.333 10 false MB 5.813,2.417 6.26,2.75 0.448,0.333 10 false 3K 3.635,3.406 4.198,3.708 0.563,0.302 10 false DOMR
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3H-19 - Auxiliary battery negative terminal Auxiliary battery positive (+) → 3K-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V
3D-9 - Auxiliary battery negative terminal Auxiliary battery positive (+) → 3K-1
Auxiliary battery negative (-) → MB-23 (DOMR)
11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
3K-1 - 3H-19 Always 10 kΩ or higher
3K-1 - 3D-9 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY