Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM3210E _58 Vehicle Interior _047531 LIGHTING (INT) _0244928 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Footwell Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the footwell lights.

WIRING DIAGRAM

E342444E03
6.219,2.896 6.844,3.219 0.625,0.323 10 false FSPT 5.875,2.99 6.5,3.313 0.625,0.323 10 false MB 5.896,2.802 6.521,3.125 0.625,0.323 10 false 26 5.438,5.708 7.083,6.292 1.646,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 3.958,5.167 6.021,5.729 2.063,0.563 10 false Instrument Panel Junction Block Assembly 0.688,4.854 1.313,5.177 0.625,0.323 10 false F4 0.688,5.021 3.417,5.448 2.729,0.427 10 false No. 1 Interior Illumination Light Assembly RH (Footwell Light RH) 0.802,4.344 1.427,4.667 0.625,0.323 10 false 2 1,4.344 1.625,4.667 0.625,0.323 10 false B 2.396,4.344 3.021,4.667 0.625,0.323 10 false L 2.573,4.344 3.198,4.667 0.625,0.323 10 false 1 0.698,3.406 1.323,3.729 0.625,0.323 10 false F5 0.698,3.573 3.417,4 2.719,0.427 10 false No. 1 Interior Illumination Light Assembly LH (Footwell Light LH) 3.625,2.99 4.25,3.313 0.625,0.323 10 false 3A 3.625,1.573 4.25,1.896 0.625,0.323 10 false 3D 3.625,0.854 4.25,1.177 0.625,0.323 10 false 3K 0.188,0.833 1.604,1.167 1.417,0.333 10 false from Auxiliary Battery 3.667,0.656 4.292,0.979 0.625,0.323 10 false 1 3.635,1.375 4.26,1.698 0.625,0.323 10 false 24 3.635,2.094 4.26,2.417 0.625,0.323 10 false 25 3.635,2.792 4.26,3.115 0.625,0.323 10 false 37 3.625,4.24 4.25,4.563 0.625,0.323 10 false 36 4.313,1.01 4.938,1.333 0.625,0.323 10 false DOME 3.625,2.292 4.25,2.615 0.625,0.323 10 false 3D 3.615,4.427 4.24,4.75 0.625,0.323 10 false 3A 2.552,2.896 3.177,3.219 0.625,0.323 10 false 1 2.396,2.896 3.021,3.219 0.625,0.323 10 false L 1.01,2.906 1.635,3.229 0.625,0.323 10 false B 0.802,2.906 1.427,3.229 0.625,0.323 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / (desired system) / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fr Foot Light Footwell light ON or OFF -
Body Electrical > Main Body > Active Test
Tester Display
Fr Foot Light
50004 123 11
OK:

Footwell lights comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3K-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

E341598C04
2.146,0.927 2.479,1.146 0.333,0.219 5.083,0.938 5.417,1.156 0.333,0.219 2.229,0.948 2.542,1.146 0.313,0.198 10 false 3D 0.271,0.198 0.583,0.396 0.313,0.198 10 false *a 5.156,0.969 5.469,1.167 0.313,0.198 10 false 3K
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3K-1 - 3D-24 Always Below 1 Ω
3K-1 - 3D-25 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (No. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (No. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F5 No. 1 interior illumination light assembly LH connector.


b.

Disconnect the F4 No. 1 interior illumination light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F5-2 (B) - 3D-25 Always Below 1 Ω
F4-2 (B) - 3D-24 Always Below 1 Ω
F5-2 (B) or 3D-25 - Body ground Always 10 kΩ or higher
F4-2 (B) or 3D-24 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (No. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (No. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F5-1 (L) - 3A-37 Always Below 1 Ω
F4-1 (L) - 3A-36 Always Below 1 Ω
F5-1 (L) or 3A-37 - Body ground Always 10 kΩ or higher
F4-1 (L) or 3A-36 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E333579C01
1.229,0.25 1.542,0.438 0.313,0.188 5,0.521 5.313,0.708 0.313,0.188 6.198,1.344 6.177,1.042 false 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.313,0.281 1.906,0.594 0.594,0.313 10 false 3A 5.073,0.552 5.667,0.865 0.594,0.313 10 false MB 6.042,1.406 6.635,1.719 0.594,0.313 10 false FSPT
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-37 - MB-26 (FSPT) Always Below 1 Ω
3A-36 - MB-26 (FSPT) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY