Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P085011  Park/Neutral Switch Circuit Short to Ground  P085015  Park/Neutral Switch Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Instead of having a parking position as one of the positions as on a conventional shift lever, a P position switch (transmission shift main switch) is provided independently above the shift lever. The switch is a momentary type, in which the button does not lock mechanically.

The P position switch (transmission shift main switch) contains resistors R1 and R2. When the P position switch (transmission shift main switch) is not pressed, the switch provides a combined resistance of R1 and R2; and when the P position switch (transmission shift main switch) is pressed, the switch provides only the resistance of R1. The voltage at the P1 terminal of the hybrid vehicle control ECU varies with the changes in the resistance of the switch. The hybrid vehicle control ECU determines the P position switch (transmission shift main switch) operation according to this resistance signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P085011 Park/Neutral Switch Circuit Short to Ground GND short in P position switch circuit
(1 trip detection logic)
·

Wire harness or connector

·

P position switch (Transmission shift main switch)

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on
P085015 Park/Neutral Switch Circuit Short to Auxiliary Battery or Open Open or +B short in P position switch circuit
(1 trip detection logic)
·

Wire harness or connector

·

P position switch (Transmission shift main switch)

·

Hybrid vehicle control ECU


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P085011
·

P Position SW Terminal Voltage*1

·

BATT Voltage

·

Shift SW Status (N,P Range)


P085015

*1: While the P position switch (transmission shift main switch) is being pushed, the value for Data List item "P Position SW Terminal Voltage" will decrease.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Depress the brake pedal and move the shift lever to select neutral (N).

7.

Push the P position switch (transmission shift main switch).

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A216493E34
5.156,1.99 6.938,2.469 1.781,0.479 10 false Hybrid Vehicle Control ECU 5.542,0.969 6.25,1.323 0.708,0.354 10 false P1 5.146,1.854 5.677,2.198 0.531,0.344 10 false F3 2.188,1.583 4.198,2.083 2.01,0.5 10 false P Position Switch (Transmission Shift Main Switch) 5.26,0.885 5.75,1.188 0.49,0.302 10 false 13 4.021,0.885 4.51,1.208 0.49,0.323 10 false 4 3.823,0.885 4.156,1.188 0.333,0.302 10 false S 3.25,1.146 3.781,1.458 0.531,0.313 10 false R2 2.625,1.146 3.083,1.417 0.458,0.271 10 false R1 2.427,0.885 3.094,1.281 0.667,0.396 10 false E 2.219,0.885 2.573,1.146 0.354,0.26 10 false 2 2.188,1.417 2.698,1.76 0.51,0.344 10 false F53

PROCEDURE

1.INSPECT P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)
a.

Disconnect the F53 P position switch (transmission shift main switch) connector.


b.
A216509C29
0.385,0.99 0.719,1.24 0.333,0.25 1.75,1.208 1.635,1.667 false 2.094,1.219 2.24,1.635 false 1.167,1.24 1.302,1.083 false 2.146,1.219 2.271,1.083 false 0.135,0.073 0.417,0.26 0.281,0.188 10 false *a 1.583,1.708 1.938,1.885 0.354,0.177 10 false S 2.219,1.688 2.573,1.865 0.354,0.177 10 false E 0.438,1.031 0.833,1.229 0.396,0.198 10 false F53
*a Component without harness connected
(P Position Switch (Transmission Shift Main Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F53-4 (S) - F53-2 (E) Switch pressed 680 Ω
F53-4 (S) - F53-2 (E) Switch released 4580 Ω


HINT:

Terminals No. 1 and No. 8 on the component side connector are empty.



c.

Reconnect the F53 P position switch (transmission shift main switch) connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))

NG

REPLACE P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Disconnect the F53 P position switch (transmission shift main switch) connector.


c.
A368382C03
1.458,2.771 1.823,3.01 0.365,0.24 1.458,0.365 1.844,0.646 0.385,0.281 2.865,2.208 2.729,1.521 true 1.552,4.167 1.604,3.802 true 0.177,2.417 0.49,2.615 0.313,0.198 10 false *b 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.521,2.813 1.875,3.031 0.354,0.219 10 false F53 1.552,0.427 1.906,0.646 0.354,0.219 10 false F3 2.823,2.26 3.135,2.458 0.313,0.198 10 false P1 1.5,4.188 1.813,4.385 0.313,0.198 10 false S
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F3-13 (P1) - F53-4 (S) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F3-13 (P1) or F53-4 (S) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-13 (P1) or F53-4 (S) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and P position switch (transmission shift main switch) connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the F53 P position switch (transmission shift main switch) connector.


j.

Reconnect the F3 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) - BODY GROUND)
a.

Disconnect the F53 P position switch (transmission shift main switch) connector.


b.
C208992C28
0.521,1.01 0.844,1.281 0.323,0.271 1.344,1.323 0.958,1.771 false 0.188,0.094 0.469,0.281 0.281,0.188 10 false *a 0.896,1.792 1.25,1.969 0.354,0.177 10 false E 0.573,1.063 0.917,1.26 0.344,0.198 10 false F53
*a Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F53-2 (E) - Body ground Power switch off Below 1 Ω



c.

Reconnect the F53 P position switch (transmission shift main switch) connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR