MALFUNCTION DESCRIPTION
The main CPU and sub CPU of the hybrid vehicle control ECU monitor their internal operation and each other for malfunctions.
The cause of this malfunction may be the following:
Hybrid vehicle control ECU malfunction
Discrepancy between motor resolver signal and actual vehicle speed
The hybrid vehicle control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P060A94 | Internal Control Module Monitoring Processor Performance Unexpected Operation | ·
The sub CPU value received by the main CPU of the hybrid control ECU exceeds the threshold for a certain period of time. ·
The hybrid vehicle control ECU detects an internal malfunction due to an abnormal calculation or sensor malfunction. (1 trip detection logic) |
Hybrid vehicle control ECU | Comes on | Master Warning Light:
Comes on |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY) and wait for 10 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Motor Generator / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Sensor and actuator circuit malfunction | P0A3F16 | Drive Motor "A" Position Sensor Circuit Voltage Below Threshold |
| P0A3F21 | Drive Motor "A" Position Sensor Signal Amplitude < Minimum | |
| P0A3F22 | Drive Motor "A" Position Sensor Signal Amplitude > Maximum | |
P060A94 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| Relevant DTC | |
|---|---|
| C1401 | Malfunction in Front Speed Sensor RH Circuit |
| C1402 | Malfunction in Front Speed Sensor LH Circuit |
| C1405 | Open or Short in Front Speed Sensor RH Circuit |
| C1406 | Open or Short in Front Speed Sensor LH Circuit |
| C1413 | Front Speed Sensor RH Circuit Output |
| C1414 | Front Speed Sensor LH Circuit Output |
P060A94 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Proceed to |
|---|
| P060A94 only is output. |
| DTCs except P060A94 are output. |
Turn the power switch off.
P060A94 only is output.
DTCs except P060A94 are output.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P060A94.
| Result | Proceed to |
|---|---|
| Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) but "Vehicle Speed" was 3 km/h (2 mph) or more | A |
| Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) and "Vehicle Speed" was less than 3 km/h (2 mph) | B |
Turn the power switch off.
A
For the inspection method of the motor resolver circuit, refer to DTC P0A3F16.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0A3F16
B