Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Drive Mode Select Switch Circuit  


DESCRIPTION

When the drive mode select switch (pattern select switch assembly) is operated, a switch signal is sent to the hybrid vehicle control ECU and the hybrid vehicle control ECU changes the drive mode.

HINT:
·

If the power switch is turned off while in POWER mode, the drive mode will automatically be changed to NORMAL mode when the power switch is turned on (IG).

·

If the power switch is turned off while in NORMAL mode or ECO mode, the selected drive mode will resume when the power switch is turned on (IG).



WIRING DIAGRAM

A373470E04
1.531,1.271 3.604,1.635 2.073,0.365 10 false Combination Meter Assembly 4.771,2.875 6.688,3.26 1.917,0.385 10 false Hybrid Vehicle Control ECU 1.385,2.771 3.542,3.24 2.156,0.469 10 false Drive Mode Select Switch (Pattern Select Switch Assembly) 0.583,3.385 2.354,3.75 1.771,0.365 10 false : CAN Communication Line 5.115,2.073 5.583,2.365 0.469,0.292 10 false PDRV 4.802,2.073 5.094,2.333 0.292,0.26 10 false 37 4.781,2.719 5.073,2.979 0.292,0.26 10 false F3 5.74,1.688 6.031,1.948 0.292,0.26 10 false +B 3.198,2.073 3.594,2.26 0.396,0.188 10 false 10 *2 2.792,2.073 3.135,2.333 0.344,0.26 10 false DRV 1.563,2.073 1.854,2.333 0.292,0.26 10 false 9 1.76,2.073 2.219,2.313 0.458,0.24 10 false E 1.396,2.625 1.688,2.885 0.292,0.26 10 false F44 3.26,1.906 3.656,2.094 0.396,0.188 10 false 3 *1 0.146,2.729 0.917,2.917 0.771,0.188 10 false *1: for LHD 0.146,3 0.917,3.188 0.771,0.188 10 false *2: for RHD

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)

A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)

A

3.CHECK DRIVE MODE STATUS (NORMAL MODE, ECO MODE, POWER MODE)

B

GO TO DTC CHART

3.CHECK DRIVE MODE STATUS (NORMAL MODE, ECO MODE, POWER MODE)
a.

Turn the power switch on (IG).


b.

Operate the drive mode select switch (pattern select switch assembly) to change the drive mode.


c.

Check that the drive mode indicator is displayed on the multi-information display and changes according to the selected drive mode.

Result:
Result Proceed to
The display changes according to the drive mode select switch (pattern select switch assembly) operation. A
The display does not change according to the drive mode select switch (pattern select switch assembly) operation. B



d.

Turn the power switch off.



A

B

4.READ VALUE USING GTS (POWERTRAIN DRIVE MODE SWITCH)
4.READ VALUE USING GTS (POWERTRAIN DRIVE MODE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Powertrain Drive Mode Switch.

Powertrain > Hybrid Control > Data List
Tester Display
Powertrain Drive Mode Switch
50003 397 324

e.

Read the value displayed on the GTS.

Powertrain > Hybrid Control
Tester Display Measurement Item Range Normal Condition
Powertrain Drive Mode Switch Drive mode select switch (pattern select switch assembly) condition ON or OFF Drive mode select switch (pattern select switch assembly) not operated: OFF
Drive mode select switch (pattern select switch assembly) being pushed and held: ON
Result:
Result Proceed to
The display changes according to the drive mode select switch (pattern select switch assembly) operation. A
The display does not change according to the drive mode select switch (pattern select switch assembly) operation. B



f.

Turn the power switch off.



A

B

5.INSPECT DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
5.INSPECT DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY)
a.

Remove the drive mode select switch (pattern select switch assembly).

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COMBINATION SWITCH>REMOVAL


b.
A338088C30
0.344,1.135 0.74,1.365 0.396,0.229 2.219,1.917 2.073,1.552 true 1.563,1.938 1.865,1.563 true 1.885,1.177 1.531,0.594 true 0.323,0.24 0.635,0.438 0.313,0.198 10 false *a 0.417,1.188 0.729,1.385 0.313,0.198 10 false F44 1.354,1.969 1.948,2.146 0.594,0.177 10 false DRV *B 2.219,1.958 2.365,2.135 0.146,0.177 10 false E 1,0.5 1.594,0.677 0.594,0.177 10 false DRV *A
*A for LHD
*B for RHD
*a Component without harness connected
(Drive Mode Select Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F44-3 (DRV) - F44-9 (E) Drive mode select switch (pattern select switch assembly) being pushed and held Below 50 Ω
Drive mode select switch (pattern select switch assembly) not pushed 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F44-10 (DRV) - F44-9 (E) Drive mode select switch (pattern select switch assembly) being pushed and held Below 50 Ω
Drive mode select switch (pattern select switch assembly) not pushed 10 kΩ or higher



c.

Install the drive mode select switch (pattern select switch assembly).


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the F44 drive mode select switch (pattern select switch assembly) connector.


b.
A338089C06
0.448,1.219 0.833,1.469 0.385,0.25 1.125,1.906 1.375,1.552 true 0.271,0.26 0.583,0.458 0.313,0.198 10 false *a 0.51,1.281 0.823,1.479 0.313,0.198 10 false F44 1.063,1.927 1.198,2.104 0.135,0.177 10 false E
*a Front view of wire harness connector
(to Drive Mode Select Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-9 (E) - Body ground Always Below 1 Ω



c.

Reconnect the F44 drive mode select switch (pattern select switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH (PATTERN SELECT SWITCH ASSEMBLY))
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Disconnect the F44 drive mode select switch (pattern select switch assembly) connector.


c.
A373477C07
0.406,3.177 0.823,3.427 0.417,0.25 1.521,0.25 1.938,0.5 0.417,0.25 2.479,2.073 2.24,1.521 true 1.219,4.021 1.583,3.573 true 1.229,2.604 1.604,3.26 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 0.25,2.563 0.563,2.719 0.313,0.156 10 false *b 0.5,3.24 0.833,3.448 0.333,0.208 10 false F44 1.667,0.313 2,0.521 0.333,0.208 10 false F3 0.927,4.073 1.625,4.281 0.698,0.208 10 false DRV *B 2.375,2.135 2.865,2.365 0.49,0.229 10 false PDRV 0.698,2.448 1.396,2.656 0.698,0.208 10 false DRV *A
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Drive Mode Select Switch (Pattern Select Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F3-37 (PDRV) - F44-3 (DRV) Always Below 1 Ω
F3-37 (PDRV) or F44-3 (DRV) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F3-37 (PDRV) - F44-10 (DRV) Always Below 1 Ω
F3-37 (PDRV) or F44-10 (DRV) - Body ground Always 10 kΩ or higher



d.

Reconnect the F44 drive mode select switch (pattern select switch assembly) connector.


e.

Reconnect the F3 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR