Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Drive Start Control System  


DESCRIPTION

The drive start control is controlled by the hybrid vehicle control ECU.

If the hybrid vehicle control ECU determines that the shift lever and accelerator pedal are operated abnormally, driving torque is restricted and, when necessary, a warning is displayed on the combination meter assembly.

C312753E08
0.344,0.25 2.656,0.469 2.313,0.219 10 false Accelerator Pedal Sensor Assembly 0.365,1.052 2.458,1.448 2.094,0.396 10 false Steering Angle Sensor and Airbag Sensor Assembly 0.406,2.198 2.573,2.833 2.167,0.635 10 false Shift Lever Position Sensor 0.396,3.406 1.979,3.813 1.583,0.406 10 false Vehicle Speed Sensor or Wheel Speed Sensor 2.917,3.771 4.031,4.125 1.115,0.354 10 false Vehicle Speed 2.896,2.604 4.26,2.875 1.365,0.271 10 false Shift State 2.677,1.458 3.99,1.885 1.313,0.427 10 false Vehicle Acceleration and Steering Angle 2.76,0.479 3.938,0.854 1.177,0.375 10 false Actual accelerator opening 5.427,1.073 7.052,1.667 1.625,0.594 10 false Meter Display Request 5.5,3.115 7.021,3.354 1.521,0.24 10 false Driving Torque Request 3.667,4.198 5.521,4.563 1.854,0.365 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

HINT:

Even if the accelerator pedal position is maintained, the system output may increase when driving uphill and decrease when driving downhill. This is due to drive start control controlling the driving torque, and is not a malfunction.


PROCEDURE

1.SYMPTOM CONFIRMATION
a.

Interview the customer to confirm the problem.


Result:
Proceed to
Hunting
Hesitation/poor acceleration



Hunting

2.PAST ACTIVATION CONFIRMATION

Hesitation/poor acceleration

8.PAST ACTIVATION CONFIRMATION
2.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions

Condition 1 (Reverse control)

Activation conditions

·

Reverse (R) is selected.

·

The accelerator pedal is depressed.

A322483E05
1.5,0.156 2.74,0.427 1.24,0.271 10 false Shift State 1.24,0.521 2.365,0.781 1.125,0.26 10 false Accelerator Pedal 2.667,0.177 2.823,0.375 0.156,0.198 10 false R 3.115,0.521 3.427,0.719 0.313,0.198 10 false ON 2.927,0.948 3.51,1.24 0.583,0.292 10 false Activated 4.625,1.563 5.365,1.823 0.74,0.26 10 false Restricted 1.573,1.573 2.458,1.896 0.885,0.323 10 false Driving Torque 3.698,2.427 4.094,2.646 0.396,0.219 10 false Time


Items Controlled

·

Driving torque is restricted.


Deactivation Conditions

·

The shift state is changed to any state other than reverse (R).

·

The accelerator pedal is released.


Condition 2 (Shift control A)

Activation conditions

·

The shift state is changed from park (P) to any forward state (drive (D) or brake (B)).

·

The accelerator pedal is depressed approximately 1/5 or more.

A322484E05
1.583,0.177 2.292,0.427 0.708,0.25 10 false Shift State 1.135,0.51 2.24,0.729 1.104,0.219 10 false Accelerator Pedal 2.594,0.188 2.771,0.438 0.177,0.25 10 false P 3.156,0.188 3.333,0.438 0.177,0.25 10 false D 2.531,0.542 2.802,0.75 0.271,0.208 10 false ON 2.927,0.823 3.573,1.063 0.646,0.24 10 false Activated 1.49,1.615 2.406,1.885 0.917,0.271 10 false Driving Torque 4.479,1.563 5.208,1.792 0.729,0.229 10 false Restricted 3.656,2.438 4.271,2.635 0.615,0.198 10 false Time

If the shift lever is moved to attempt to change the shift state from park (P) when the accelerator pedal is depressed, the shift state will not change and drive-start control will not operate.



Items Controlled

·

Driving torque is restricted.


Deactivation Conditions

·

Shift state is changed to park (P) or neutral (N).

·

The accelerator pedal is released.


Condition 3 (Shift control B)

Activation conditions

·

The shift state is changed from reverse (R) to any forward state (drive (D) or brake (B)), any forward state (drive (D) or brake (B)) to reverse (R), or Neutral (N) to reverse (R).

·

The accelerator pedal is depressed approximately 1/5 or more.

A322485E05
1.594,0.167 2.302,0.458 0.708,0.292 10 false Shift State 1.156,0.531 2.302,0.771 1.146,0.24 10 false Accelerator Pedal 2.594,0.177 2.75,0.375 0.156,0.198 10 false N 3.156,0.188 3.313,0.385 0.156,0.198 10 false R 2.531,0.542 2.833,0.771 0.302,0.229 10 false ON 2.917,0.802 3.521,1.031 0.604,0.229 10 false Activated 1.49,1.625 2.375,1.885 0.885,0.26 10 false Driving Torque 3.615,2.427 4.229,2.625 0.615,0.198 10 false Time 4.573,1.542 5.375,1.813 0.802,0.271 10 false Restricted


Items Controlled

·

Driving torque is restricted.


Deactivation Conditions

·

Shift state is changed to park (P) or neutral (N).

·

The accelerator pedal is released.



HINT:

During reverse control or shift control, driving torque is adjusted based on the road gradient and steering angle.



Result:
Proceed to
Performed
Not performed



Performed

3.CHECK DTC OUTPUT (HEALTH CHECK)

Not performed

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


f.

Turn the power switch off.


Result:
Proceed to
DTCs are not output
DTC is output



DTCs are not output

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

DTC is output

GO TO DTC CHART

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) When driving at constant speed: No large fluctuations

e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at constant speed between 16 to 64 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (VEHICLE SPEED)

NG

5.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Speed.

Powertrain > Hybrid Control > Data List
Tester Display
Vehicle Speed
50003 397 12

e.

Read the value of "Vehicle Speed" displayed on the GTS.

Standard:
Inspection Condition Specified Condition
Vehicle stopped 0 km/h (0 mph)
Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph))
No large fluctuations in displayed speed


CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (DECELERATION SENSOR)

NG

INSPECT ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

6.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Deceleration Sensor and Deceleration Sensor2.

Chassis > ABS/VSC/TRAC > Data List
Tester Display
Deceleration Sensor
Deceleration Sensor2
50003 105 14,15

e.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Deceleration Sensor
Deceleration Sensor2
During deceleration Value changes with vehicle speed
During acceleration Value changes with vehicle speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (STEERING ANGLE SENSOR)

NG

7.READ VALUE USING GTS (STEERING ANGLE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Steering Angle Sensor.

Chassis > ABS/VSC/TRAC > Data List
Tester Display
Steering Angle Sensor
50003 105 26
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition
Steering Angle Sensor Steering angle sensor Min.: -3276.8 degrees, Max.: 3276.7 degrees Turning left: Increases
Turning right: Decreases

e.

Read the value displayed on the GTS.

Standard:
Condition Specified Condition
Steering wheel turned left Value increases with steering wheel operation
Steering wheel turned right Value decreases with steering wheel operation


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

8.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions

Condition 1 (Reverse control)

Activation conditions

·

Reverse (R) is selected .

·

The accelerator pedal is depressed.

A322483E06
1.667,0.156 2.74,0.427 1.073,0.271 10 false Shift State 1.24,0.521 2.365,0.781 1.125,0.26 10 false Accelerator Pedal 2.667,0.177 2.823,0.375 0.156,0.198 10 false R 3.115,0.521 3.427,0.719 0.313,0.198 10 false ON 2.927,0.948 3.51,1.24 0.583,0.292 10 false Activated 4.625,1.563 5.365,1.823 0.74,0.26 10 false Restricted 1.573,1.573 2.458,1.896 0.885,0.323 10 false Driving Torque 3.698,2.427 4.094,2.646 0.396,0.219 10 false Time


Items Controlled

·

Driving torque is restricted.


Deactivation Conditions

·

The shift state is changed to any state other than reverse (R).

·

The accelerator pedal is released.


Condition 2 (Shift control A)

Activation conditions

·

The shift state is changed from park (P) to any forward state (drive (D) or reverse (R)).

·

The accelerator pedal is depressed approximately 1/5 or more.

A322484E05
1.583,0.177 2.292,0.427 0.708,0.25 10 false Shift State 1.135,0.51 2.24,0.729 1.104,0.219 10 false Accelerator Pedal 2.594,0.188 2.771,0.438 0.177,0.25 10 false P 3.156,0.188 3.333,0.438 0.177,0.25 10 false D 2.531,0.542 2.802,0.75 0.271,0.208 10 false ON 2.927,0.823 3.573,1.063 0.646,0.24 10 false Activated 1.49,1.615 2.406,1.885 0.917,0.271 10 false Driving Torque 4.479,1.563 5.208,1.792 0.729,0.229 10 false Restricted 3.656,2.438 4.271,2.635 0.615,0.198 10 false Time


Items Controlled

·

Driving torque is restricted.


Deactivation Conditions

·

Shift state is changed to park (P) or neutral (N).

·

The accelerator pedal is released.


Condition 3 (Shift control B)

Activation conditions

·

The shift state is changed from reverse (R) to any forward state (drive (D) or brake (B)), any forward state (drive (D) or brake (B)) to reverse (R), or neutral (N) to reverse (R).

·

The accelerator pedal is depressed approximately 1/5 or more.

A322485E05
1.594,0.167 2.302,0.458 0.708,0.292 10 false Shift State 1.156,0.531 2.302,0.771 1.146,0.24 10 false Accelerator Pedal 2.594,0.177 2.75,0.375 0.156,0.198 10 false N 3.156,0.188 3.313,0.385 0.156,0.198 10 false R 2.531,0.542 2.833,0.771 0.302,0.229 10 false ON 2.917,0.802 3.521,1.031 0.604,0.229 10 false Activated 1.49,1.625 2.375,1.885 0.885,0.26 10 false Driving Torque 3.615,2.427 4.229,2.625 0.615,0.198 10 false Time 4.573,1.542 5.375,1.813 0.802,0.271 10 false Restricted


Items Controlled

·

Driving torque is restricted.


Deactivation Conditions

·

Shift state is changed to park (P) or neutral (N).

·

The accelerator pedal is released.



HINT:

During reverse control or shift control, driving torque is adjusted based on the road gradient and steering angle.


Result:
Result Proceed to
Not performed A
Performed B


HINT:

If the customer operated the vehicle in a way which caused the drive start control to operate, explain the operation of the system to the customer and that the operation is not a malfunction.




A

9.CHECK DTC OUTPUT (HEALTH CHECK)

B

SYSTEM NORMAL

9.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC is output B


f.

Turn the power switch off.



A

10.READ VALUE USING GTS (SHIFT POSITION)

B

GO TO DTC CHART

10.READ VALUE USING GTS (SHIFT POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Position.

Powertrain > Hybrid Control > Data List
Tester Display
Shift Position
50003 397 231
Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Shift Position Current shift state P/R/N/D/B Matches currently selected shift state:
P, R, N, D or B

e.

Read the value displayed on the GTS.

OK:
Condition Specified Condition
Select shift state Matches currently selected shift state



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

NG

11.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accelerator Position Sensor No.1 Voltage %, Accelerator Position Sensor No.2 Voltage %.

Powertrain > Hybrid Control > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24
Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Accelerator Position Sensor No.1 Voltage % Accelerator pedal position sensor No. 1 Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Changes with accelerator pedal pressure
Accelerator Position Sensor No.2 Voltage % Accelerator pedal position sensor No. 2 Min.: 0.0%, Max.: 100.0% Accelerator pedal depressed:
Accelerator pedal depressed:

e.

Read the value displayed on the GTS.

OK:
Condition Specified Condition
Accelerator Pedal Released → Depressed Values smoothly change following accelerator pedal operation



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY