Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the navigation receiver assembly.

WIRING DIAGRAM

E334511E01
1.208,0.542 2.698,0.823 1.49,0.281 10 false from Auxiliary Battery 1.531,1.104 3.021,1.385 1.49,0.281 10 false from ACC Relay 1.219,1.677 2.708,1.958 1.49,0.281 10 false from IG1-NO. 1 Relay 3.729,0.719 4.281,1.021 0.552,0.302 10 false RADIO 3.646,1.271 5.135,1.552 1.49,0.281 10 false ECU-ACC 3.521,1.844 5.01,2.125 1.49,0.281 10 false ECU-IG1 NO. 4 5.052,2.771 6.938,3.125 1.885,0.354 10 false Navigation Receiver Assembly 5.198,2.24 5.521,2.458 0.323,0.219 10 false F93 5.281,2.042 5.604,2.26 0.323,0.219 10 false 7 5.208,1.677 5.531,1.896 0.323,0.219 10 false F92 5.271,1.49 5.594,1.708 0.323,0.219 10 false 1 5.198,1.125 5.521,1.344 0.323,0.219 10 false F93 5.271,0.927 5.594,1.146 0.323,0.219 10 false 3 5.198,0.563 5.521,0.781 0.323,0.219 10 false F93 5.281,0.365 5.604,0.583 0.323,0.219 10 false 4 5.583,0.563 6.135,0.875 0.552,0.313 10 false +B1 5.594,1.115 6.146,1.427 0.552,0.313 10 false ACC1 5.594,1.677 6.146,1.99 0.552,0.313 10 false IG 5.583,2.24 6.135,2.552 0.552,0.313 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the F93 and F92 navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F93-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F93-4 (+B1) - F93-7 (GND1) Power switch off 11 to 14 V
F93-3 (ACC1) - F93-7 (GND1) Power switch on (ACC) 11 to 14 V
F92-1 (IG) - F93-7 (GND1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR