Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E276615E11
2.948,2.208 4.927,2.396 1.979,0.188 10 false : AVC-LAN Communication Line 1.01,1.469 1.469,1.667 0.458,0.198 10 false F61 5.094,0.583 5.552,0.781 0.458,0.198 10 false TX1+ 4.865,1.615 6.885,1.906 2.021,0.292 10 false Navigation Receiver Assembly 1,1.625 2.198,2.177 1.198,0.552 10 false Stereo Component Amplifier Assembly 4.875,1.469 5.333,1.667 0.458,0.198 10 false F92 5.104,0.979 5.563,1.177 0.458,0.198 10 false TX1- 4.906,0.448 5.104,0.625 0.198,0.177 10 false 7 4.906,0.833 5.104,1.01 0.198,0.177 10 false 8 1.844,0.573 2.302,0.771 0.458,0.198 10 false TX+ 1.875,0.948 2.115,1.156 0.24,0.208 10 false TX- 2.177,0.448 2.375,0.625 0.198,0.177 10 false 8 2.177,0.833 2.375,1.01 0.198,0.177 10 false 7

CAUTION / NOTICE / HINT

HINT:

The navigation receiver assembly is the master unit.


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E221758C34
1.479,0.417 1.969,0.667 0.49,0.25 1.365,1.729 1.615,1.229 false 2.083,1.729 1.802,1.219 false 0.135,0.083 0.667,0.458 0.531,0.375 10 false *a 1.208,1.771 1.583,2.021 0.375,0.25 10 false TX1- 1.99,1.771 2.521,2 0.531,0.229 10 false TX1+ 1.594,0.448 2.104,0.719 0.51,0.271 10 false F92
*a Component without harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-7 (TX1+) - F92-8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the F61 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-7 (TX1+) - F61-8 (TX+) Always Below 1 Ω
F92-8 (TX1-) - F61-7 (TX-) Always Below 1 Ω
F92-7 (TX1+) or F61-8 (TX+) - Body ground Always 10 kΩ or higher
F92-8 (TX1-) or F61-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG