Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function)
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0245086 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Entry Exterior Alarm and Answer-back Buzzer do not Sound  


DESCRIPTION

The entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.

WIRING DIAGRAM

B388643E23
2.365,1.042 2.823,1.24 0.458,0.198 10 false 3F 0.531,1.5 0.99,1.698 0.458,0.198 10 false A30 0.531,1.677 1.792,2.083 1.26,0.406 10 false Wireless Door Lock Buzzer 2.344,0.844 2.802,1.042 0.458,0.198 10 false 29 3.677,0.865 4.135,1.063 0.458,0.198 10 false 21 3.646,1.042 4.104,1.24 0.458,0.198 10 false MB 3.958,0.938 4.417,1.135 0.458,0.198 10 false BZR 4.271,0.542 4.729,0.74 0.458,0.198 10 false +B 1.51,0.958 1.74,1.146 0.229,0.188 10 false B 1.719,0.958 1.948,1.146 0.229,0.188 10 false 1 0.688,0.948 0.917,1.135 0.229,0.188 10 false E 0.5,0.948 0.729,1.135 0.229,0.188 10 false 2 2.25,1.583 3.865,2.01 1.615,0.427 10 false Instrument Panel Junction Block Assembly 5.531,2.677 7.073,3.198 1.542,0.521 10 false Certification ECU (Smart Key ECU Assembly) 0.646,3.219 2.417,3.458 1.771,0.24 10 false : CAN Communication Line 3.604,2.719 5.271,3.125 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output.



PROCEDURE

1.CHECK CUSTOMIZE SETTING (WIRELESS BUZZER RESP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.

Wireless Door Lock
Tester Display Description Default Setting ECU
Wireless Buzzer Resp Wireless buzzer response ON 0:OFF,1:ON Main body ECU (multiplex network body ECU)
50006 1

Result:
Result Proceed to
"ON" is displayed A
"OFF" is displayed B



A

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

B

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

3.READ VALUE USING GTS (EACH UNLOCK DETECTION SWITCH)

B

3.READ VALUE USING GTS (EACH UNLOCK DETECTION SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door RH unlocked
LOCK: Front door RH locked
-
FL Door Lock Pos Front door LH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door LH unlocked
LOCK: Front door LH locked
-
RR-Door Lock Pos SW Rear door RH unlock detection switch signal ON or OFF ON: Rear door RH unlocked
OFF: Rear door RH locked
-
RL-Door Lock Pos SW Rear door LH unlock detection switch signal ON or OFF ON: Rear door LH unlocked
OFF: Rear door LH locked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
RR-Door Lock Pos SW
RL-Door Lock Pos SW
50003 123 196,198,51,52
OK:

The GTS display changes correctly in response to the lock/unlock operation.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

5.CHECK WIRELESS DOOR LOCK BUZZER

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK WIRELESS DOOR LOCK BUZZER
a.

Disconnect the A30 wireless door lock buzzer connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Active Test.


f.

Perform Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 123 12

g.
B222362C41
1.5,0.427 1.865,0.698 0.365,0.271 2.104,1.875 1.802,1.385 false 1.208,1.885 1.552,1.375 false 0.24,0.198 0.552,0.396 0.313,0.198 10 false *a 1.563,0.469 1.875,0.667 0.313,0.198 10 false A30 1.104,1.906 1.375,2.104 0.271,0.198 10 false B 2.094,1.906 2.25,2.104 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Wireless Door Lock Buzzer)


While performing the Active Test, measure the voltage between the terminals of the wireless door lock buzzer.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-1 (B) - A30-2 (E) Active Test Wireless Buzzer ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)
Active Test Wireless Buzzer OFF Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE WIRELESS DOOR LOCK BUZZER

NG

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the A30 wireless door lock buzzer connector.


c.

Reconnect the 3F instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (B) - MB-21 (BZR) Always Below 1 Ω
A30-2 (E) - Body ground Always Below 1 Ω
A30-1 (B) or MB-21 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

7.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.

Disconnect the A30 wireless door lock buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-1 (B) - 3F-29 (BZR) Always Below 1 Ω
A30-1 (B) or 3F-29 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR