Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM3210E _59 Vehicle Exterior _047515 WINDOW / GLASS _0245124 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter  


DESCRIPTION

Wireless Transmitter-linked Function*

When an electronic key transmitter sub-assembly switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assemblies; and 4) the power window regulator motor assemblies are activated.

*: w/o Canister Pump Module



Key-linked Function

When the driver door key cylinder (key linked switch) is turned and held: 1) the door lock motor receives the signal; 2) the main body ECU (multiplex network body ECU) sends the signal to the power window regulator motor assemblies; and 3) the power window regulator motor assemblies are activated.


CAUTION / NOTICE / HINT

NOTICE:
·

These functions are set through customize settings, as they are off by default.

·

The power window control system uses the LIN communication system and CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Check that power window system customize setting "Door Key P/W Up", "Door Key P/W Down", "P/W Up W/Transmit"* and "P/W Down W/Transmit"* are set to "ON" before performing the following procedure.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS

*: w/o Canister Pump Module


·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK BASIC FUNCTION (WIRELESS AND POWER DOOR LOCK CONTROL SYSTEM)
a.

Check that the wireless door lock/unlock function operates normally.*

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

*: w/o Canister Pump Module



b.

Check that the key-linked lock/unlock function operates normally.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock function and key-linked lock/unlock function operate normally A
Wireless door lock/unlock function does not operate normally B
Key-linked lock/unlock function does not operate normally C



A

2.CHECK MANUAL UP / DOWN FUNCTION

B

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

C

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

2.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down functions using the multiplex network master switch assembly and power window regulator switch assembly can operate all of the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Manual up and down functions are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK REMOTE UP / DOWN FUNCTION

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

3.CHECK REMOTE UP / DOWN FUNCTION
a.

Check that the remote up and down functions using the multiplex network master switch assembly can operate all of the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Remote up and down functions are normal.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)