Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1259  HV Control System Regenerative Malfunction  C1310  HV System Malfunction  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) communicates with the hybrid vehicle control ECU and controls braking force according to the motor's regenerative force.

The skid control ECU (brake booster with master cylinder assembly) sends VSC+/VSC and cooperative control with EPS signals to the hybrid vehicle control ECU and receives operating signals from the hybrid vehicle control ECU.

The skid control ECU (brake booster with master cylinder assembly) uses CAN communication for communicating with the hybrid vehicle control ECU. If a communication malfunction is detected, the skid control ECU (brake booster with master cylinder assembly) prohibits VSC+/VSC and cooperative control with EPS operation and part of the electronically controlled brake system control as a fail-safe function.

If the signals from the hybrid vehicle control ECU return to normal, the warning light will go off and the DTCs C1259 and C1310 will be cleared.

HINT:

These DTCs will be output from the skid control ECU (brake booster with master cylinder assembly) when the hybrid vehicle control ECU sends a malfunction signal to the skid control ECU (brake booster with master cylinder assembly).


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1259 HV Control System Regenerative Malfunction 1132 A regeneration malfunction signal is input for at least 0.036 seconds when IG2 terminal voltage is 9.5 V or more for at least 2 seconds and communication with the hybrid vehicle control ECU is valid.
·

Hybrid vehicle control ECU

(Regeneration malfunction)

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
HINT:

The DTC is cleared when the conditions return to normal.


C1310 HV System Malfunction 1140 When the IG2 terminal voltage is 9.5 V or more for 2 seconds or more and communication with the hybrid vehicle control ECU is possible, an internal malfunction signal is detected for 0.072 seconds or more.
·

Hybrid vehicle control ECU

·

Skid control ECU (brake booster with master cylinder assembly)


VSC DTC
HINT:

The DTC is cleared when the conditions return to normal.



CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC (HYBRID CONTROL SYSTEM)
a.

Check if a hybrid control system DTCs are output.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK DTC (MOTOR GENERATOR CONTROL SYSTEM)

B

2.CHECK DTC (MOTOR GENERATOR CONTROL SYSTEM)
a.

Check if a motor generator control system DTCs are output.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Motor Generator > Trouble Codes
50001 395

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.CHECK DTC (SFI SYSTEM)

B

3.CHECK DTC (SFI SYSTEM)
a.

Check if a SFI system DTCs are output.

w/ Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

w/o Canister Pump Module: Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.PROBLEM SYMPTOMS TABLE (HYBRID CONTROL SYSTEM)

B

4.PROBLEM SYMPTOMS TABLE (HYBRID CONTROL SYSTEM)
a.

Check the Problem Symptoms Table of the hybrid control system.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE

OK:

No malfunctions in the Problem Symptoms Table are occurring.



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR MALFUNCTIONING PART

5.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1259 and/or C1310 are output. A
DTCs other than C1259 and C1310 are output. B
DTCs are not output. C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

C