The linear solenoids SLA and SLR control the regulator based on signals from the skid control ECU (brake booster with master cylinder assembly) and produce servo pressure in accordance with the vehicle condition.
When the system is normal, the switching solenoid SGH is opened to allow brake fluid to flow to the stroke simulator when the brake pedal is depressed. When the system is abnormal, the switching solenoid SGH closes to prevent the flow of brake fluid.
When the system is normal, the switching solenoid SSA is closed. When the system is abnormal, the switching solenoid SSA is opened to allow fluid to flow to the brake master cylinder reservoir assembly.
If the supply voltage decreases, a drop in current may cause DTCs to be stored.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1211 | SLA Linear Solenoid | 21
22 23 24 25 26 |
·
INF Code: 21 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 22 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 23 ·
An excessive current is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 24 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 25 ·
A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 26 ·
Insufficient current is detected in the solenoid for 0.05 seconds or more. |
·
INF Code: 21, 22, 24 ·
Brake booster with master cylinder assembly ·
INF Code: 23 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly ·
INF Code: 25, 26 ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1212 | SLR Linear Solenoid | 31
32 33 34 35 36 |
·
INF Code: 31 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 32 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 33 ·
An excessive current is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 34 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 35 ·
A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 36 ·
Insufficient current is detected in the solenoid for 0.05 seconds or more. |
·
INF Code: 31, 32, 34 ·
Brake booster with master cylinder assembly ·
INF Code: 33 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly ·
INF Code: 35, 36 ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1225 | SA1 Solenoid Circuit | 41
42 43 44 45 46 |
·
INF Code: 41 ·
Overcurrent is detected in SSA for 0.05 seconds or more. ·
INF Code: 42 ·
An open is detected in SSA for 0.05 seconds or more. ·
INF Code: 43 ·
Monitoring value of SSA continues to be excessively higher than request value. ·
INF Code: 44 ·
Current leakage is detected in SSA for 0.05 seconds or more. ·
INF Code: 45 ·
A malfunction in the SSA current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 46 ·
Monitoring value of SSA continues to be excessively lower than request value. |
·
INF Code: 41, 42, 44 ·
Brake booster with master cylinder assembly ·
INF Code: 43 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly ·
INF Code: 45, 46 ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
| C1226 | SA2 Solenoid Circuit | 71
72 73 74 75 76 |
·
INF Code: 71 ·
Overcurrent is detected in SGH for 0.05 seconds or more. ·
INF Code: 72 ·
An open is detected in SGH for 0.05 seconds or more. ·
INF Code: 73 ·
Monitoring value of SGH continues to be excessively higher than request value. ·
INF Code: 74 ·
Current leakage is detected in SGH for 0.05 seconds or more. ·
INF Code: 75 ·
A malfunction in the SGH current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 76 ·
Monitoring value of SGH continues to be excessively lower than request value. |
·
INF Code: 71, 72, 74 ·
Brake booster with master cylinder assembly ·
INF Code: 73 ·
Supply voltage reduced ·
Brake booster with master cylinder assembly ·
INF Code: 75, 76 ·
Brake booster with master cylinder assembly |
Electronically controlled brake system DTC |
After replacing the brake booster with master cylinder assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check if the same DTC is output.
If a DTC for undervoltage is output, first troubleshoot the power source system.
| Result | Proceed to |
|---|---|
| DTCs C1211, C1212, C1225 and C1226 are not output. | A |
| A DTC related to low voltage is output. | B |
| DTCs C1211, C1212, C1225 and/or C1226 are output. | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL