Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C349892E03
5.354,0.938 5.792,1.125 0.438,0.188 10 false CA1L 5.083,0.76 5.396,0.958 0.313,0.198 10 false 42 5.083,1.573 5.396,1.771 0.313,0.198 10 false 43 5.354,1.76 5.833,2.01 0.479,0.25 10 false CA1H 6.375,2.865 6.688,3.063 0.313,0.198 10 false IC 5.323,2.99 5.802,3.229 0.479,0.24 10 false CSW 5.094,2.781 5.406,2.979 0.313,0.198 10 false 18 4.729,2.771 5.042,2.969 0.313,0.198 10 false 2 4.531,2.99 4.844,3.188 0.313,0.198 10 false + 3.844,2.99 4.156,3.188 0.313,0.198 10 false E 3.656,2.781 3.969,2.979 0.313,0.198 10 false 6 3.26,3.208 3.573,3.406 0.313,0.198 10 false F12 3.271,3.385 5.208,3.771 1.938,0.385 10 false VSC OFF Switch (Combination Switch Assembly) 5.073,3.917 5.385,4.115 0.313,0.198 10 false A41 5.063,4.115 7.125,4.542 2.063,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.927,4.344 4.75,4.573 1.823,0.229 10 false : CAN Communication Line 0.125,3.917 0.438,4.115 0.313,0.198 10 false F6 0.115,4.073 1.938,4.479 1.823,0.406 10 false Combination Meter Assembly (Meter Circuit Plate) 0.896,1.74 1.354,1.969 0.458,0.229 10 false CANH 1.396,1.563 1.708,1.76 0.313,0.198 10 false 26 0.906,0.948 1.365,1.177 0.458,0.229 10 false CANL 1.396,0.76 1.708,0.958 0.313,0.198 10 false 27

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, VSC Expert Mode or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC Expert Mode: VSC expert mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

b.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (Traction Control Turned Off) VSC OFF Indicator Light
Not pressed Normal Not displayed Does not come on
Pressing the VSC OFF switch (combination switch assembly) TRC OFF Displayed Does not come on
Pressing and holding the VSC OFF switch (combination switch assembly) VSC OFF Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

4.PERFORM ACTIVE TEST USING GTS (MULTI-INFORMATION DISPLAY (TRACTION CONTROL TURNED OFF) AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (MULTI-INFORMATION DISPLAY (TRACTION CONTROL TURNED OFF) AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light Multi-information display (Traction Control Turned Off) Display ON/OFF Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the multi-information display (Traction Control Turned Off) and VSC OFF indicator light on the combination meter assembly turn on or off in accordance with GTS operation.

OK:

The multi-information display (Traction Control Turned Off) and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION SWITCH ASSEMBLY

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT COMBINATION SWITCH ASSEMBLY
a.
C305912C60
2.156,1.469 2.406,1.781 true 1.927,1.083 2.104,0.563 true 0.188,0.115 0.5,0.313 0.313,0.198 10 false *a 2.104,0.406 2.417,0.625 0.313,0.219 10 false + 2.427,1.813 3.063,1.969 0.635,0.156 10 false E
*a Component without harness connected
(VSC OFF Switch (Combination Switch Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the F12 VSC OFF switch (combination switch assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 6 (E) Switch pushed Below 1 Ω
2 (+) - 6 (E) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - COMBINATION SWITCH ASSEMBLY)

NG

REPLACE COMBINATION SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - COMBINATION SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-18 (CSW) - F12-2 (+) Always Below 1 Ω
A41-18 (CSW) or F12-2 (+) - Body ground Always 10 kΩ or higher
F12-6 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly (meter CPU) using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

b.

Check the combination meter assembly.

OK:

The multi-information display and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG