Each solenoid adjusts the pressure which affects each wheel cylinder according to signals from the skid control ECU (brake booster with master cylinder assembly) and controls the vehicle.
| DTC No. | Detection Item | INF Code | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|---|
| C1352 | Increasing Pressure Solenoid (FR) | 11
1100 1101 1102 1103 1170 |
·
INF Code: 11 ·
A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 1100 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1101 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1102 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1103 ·
A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more. ·
INF Code: 1170 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1353 | Increasing Pressure Solenoid (FL) | 13
1106 1107 1108 1109 1172 |
·
INF Code: 13 ·
A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 1106 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1107 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1108 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1109 ·
A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more. ·
INF Code: 1172 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1354 | Increasing Pressure Solenoid (RR) | 15
1112 1113 1114 1115 1174 |
·
INF Code: 15 ·
A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 1112 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1113 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1114 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1115 ·
A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more. ·
INF Code: 1174 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1355 | Increasing Pressure Solenoid (RL) | 17
1118 1119 1120 1121 1176 |
·
INF Code: 17 ·
A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more. ·
INF Code: 1118 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1119 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1120 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1121 ·
A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more. ·
INF Code: 1176 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1356 | Decreasing Pressure Solenoid (FR) | 12
1104 1105 1171 |
·
INF Code: 12 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1104 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1105 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1171 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1357 | Decreasing Pressure Solenoid (FL) | 14
1110 1111 1173 |
·
INF Code: 14 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1110 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1111 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1173 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1358 | Decreasing Pressure Solenoid (RR) | 16
1116 1117 1175 |
·
INF Code: 16 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1116 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1117 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1175 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
| C1359 | Decreasing Pressure Solenoid (RL) | 18
1122 1123 1177 |
·
INF Code: 18 ·
An open is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1122 ·
Overcurrent is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1123 ·
Current leakage is detected in the solenoid for 0.05 seconds or more. ·
INF Code: 1177 ·
The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more. |
·
Wire harness or connector ·
Brake actuator assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Electronically controlled brake system DTC |
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(Brake Actuator Assembly) |
- | - |
Disconnect the A42 brake actuator assembly connector (for LHD).
Disconnect the A43 brake actuator assembly connector (for RHD).
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
Check the brake actuator assembly when it is cooled down.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 38 (+BS) - 8 (SFRH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 37 (SFLH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 11 (SRRH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 34 (SRLH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 2 (SFRR) | Always | 5.1 to 5.7 Ω |
| 38 (+BS) - 31 (SFLR) | Always | 5.1 to 5.7 Ω |
| 38 (+BS) - 5 (SRRR) | Always | 5.1 to 5.7 Ω |
| 38 (+BS) - 28 (SRLR) | Always | 5.1 to 5.7 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 38 (+BS) - 37 (SFRH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 8 (SFLH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 34 (SRRH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 11 (SRLH) | Always | 6.4 to 7.0 Ω |
| 38 (+BS) - 31 (SFRR) | Always | 5.1 to 5.7 Ω |
| 38 (+BS) - 2 (SFLR) | Always | 5.1 to 5.7 Ω |
| 38 (+BS) - 28 (SRRR) | Always | 5.1 to 5.7 Ω |
| 38 (+BS) - 5 (SRLR) | Always | 5.1 to 5.7 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(for RHD)>REMOVAL
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-14 (+BS) - A42-38 (+BS) | Always | Below 1 Ω |
| A41-14 (+BS) or A42-38 (+BS) - Body ground | Always | 10 kΩ or higher |
| A41-48 (SFRH) - A42-8 (SFRH) | Always | Below 1 Ω |
| A41-48 (SFRH) or A42-8 (SFRH) - Body ground | Always | 10 kΩ or higher |
| A41-49 (SFLH) - A42-37 (SFLH) | Always | Below 1 Ω |
| A41-49 (SFLH) or A42-37 (SFLH) - Body ground | Always | 10 kΩ or higher |
| A41-50 (SRRH) - A42-11 (SRRH) | Always | Below 1 Ω |
| A41-50 (SRRH) or A42-11 (SRRH) - Body ground | Always | 10 kΩ or higher |
| A41-51 (SRLH) - A42-34 (SRLH) | Always | Below 1 Ω |
| A41-51 (SRLH) or A42-34 (SRLH) - Body ground | Always | 10 kΩ or higher |
| A41-44 (SFRR) - A42-2 (SFRR) | Always | Below 1 Ω |
| A41-44 (SFRR) or A42-2 (SFRR) - Body ground | Always | 10 kΩ or higher |
| A41-45 (SFLR) - A42-31 (SFLR) | Always | Below 1 Ω |
| A41-45 (SFLR) or A42-31 (SFLR) - Body ground | Always | 10 kΩ or higher |
| A41-46 (SRRR) - A42-5 (SRRR) | Always | Below 1 Ω |
| A41-46 (SRRR) or A42-5 (SRRR) - Body ground | Always | 10 kΩ or higher |
| A41-47 (SRLR) - A42-28 (SRLR) | Always | Below 1 Ω |
| A41-47 (SRLR) or A42-28 (SRLR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-14 (+BS) - A43-38 (+BS) | Always | Below 1 Ω |
| A41-14 (+BS) or A43-38 (+BS) - Body ground | Always | 10 kΩ or higher |
| A41-48 (SFRH) - A43-37 (SFRH) | Always | Below 1 Ω |
| A41-48 (SFRH) or A43-37 (SFRH) - Body ground | Always | 10 kΩ or higher |
| A41-49 (SFLH) - A43-8 (SFLH) | Always | Below 1 Ω |
| A41-49 (SFLH) or A43-8 (SFLH) - Body ground | Always | 10 kΩ or higher |
| A41-50 (SRRH) - A43-34 (SRRH) | Always | Below 1 Ω |
| A41-50 (SRRH) or A43-34 (SRRH) - Body ground | Always | 10 kΩ or higher |
| A41-51 (SRLH) - A43-11 (SRLH) | Always | Below 1 Ω |
| A41-51 (SRLH) or A43-11 (SRLH) - Body ground | Always | 10 kΩ or higher |
| A41-44 (SFRR) - A43-31 (SFRR) | Always | Below 1 Ω |
| A41-44 (SFRR) or A43-31 (SFRR) - Body ground | Always | 10 kΩ or higher |
| A41-45 (SFLR) - A43-2 (SFLR) | Always | Below 1 Ω |
| A41-45 (SFLR) or A43-2 (SFLR) - Body ground | Always | 10 kΩ or higher |
| A41-46 (SRRR) - A43-28 (SRRR) | Always | Below 1 Ω |
| A41-46 (SRRR) or A43-28 (SRRR) - Body ground | Always | 10 kΩ or higher |
| A41-47 (SRLR) - A43-5 (SRLR) | Always | Below 1 Ω |
| A41-47 (SRLR) or A43-5 (SRLR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.
Reconnect the A42 brake actuator assembly connector (for LHD).
Reconnect the A43 brake actuator assembly connector (for RHD).
Clear the DTCs.
Turn the power switch off.
Turn the power switch on (IG).
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 and C1359 are not output. | A |
| DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 and/or C1359 are output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL