Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1413 and C1414.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1413

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1405 Open or Short in Front Speed Sensor RH Circuit 503
506
508
·

INF Code: 503

·

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 506

·

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 508

·

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Front speed sensor RH

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC
C1406 Open or Short in Front Speed Sensor LH Circuit 513
516
518
·

INF Code: 513

·

An open in the speed sensor signal circuit continues for 0.5 seconds or more.


·

INF Code: 516

·

The speed sensor power source voltage is low for 0.5 seconds or more.


·

INF Code: 518

·

The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more.



·

Front speed sensor LH

·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


ABS DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Open Front speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

b.

Check the speed sensor output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1405 and C1406 are not output. A
DTCs C1405 and/or C1406 are output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A31 or A15 front speed sensor connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A41-3 (FR+) - A31-1 (FR+) Always Below 1 Ω
A41-3 (FR+) or A31-1 (FR+) - Body ground Always 10 kΩ or higher
A41-4 (FR-) - A31-2 (FR-) Always Below 1 Ω
A41-4 (FR-) or A31-2 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A41-31 (FL+) - A15-1 (FL+) Always Below 1 Ω
A41-31 (FL+) or A15-1 (FL+) - Body ground Always 10 kΩ or higher
A41-32 (FL-) - A15-2 (FL-) Always Below 1 Ω
A41-32 (FL-) or A15-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C248346C20
0.802,1.01 1.24,1.281 0.438,0.271 2.208,1.01 2.646,1.281 0.438,0.271 1.615,2.813 1.156,1.979 true 3,2.771 2.563,1.99 true 0.229,0.271 0.531,0.5 0.302,0.229 10 false *a 1.552,2.833 1.865,3.042 0.313,0.208 10 false FR+ 2.938,2.813 3.271,3.042 0.333,0.229 10 false FL+ 0.896,1.063 1.427,1.323 0.531,0.26 10 false A31 2.302,1.063 2.938,1.458 0.635,0.396 10 false A15 0.542,1.073 0.844,1.302 0.302,0.229 10 false *A 1.969,1.073 2.271,1.302 0.302,0.229 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A31-1 (FR+) - Body ground Power switch on (IG) 8 to 14 V

for LH
Tester Connection Condition Specified Condition
A15-1 (FL+) - Body ground Power switch on (IG) 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY