Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1432  Steering Angle Sensor Power Source Voltage  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1432 Steering Angle Sensor Power Source Voltage 703 Steering angle sensor power supply malfunction signal is received from steering angle sensor.
·

Wire harness or connector

·

Steering angle sensor


VSC DTC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C269831C18
0.406,1 0.854,1.323 0.448,0.323 2.146,2.604 2.479,2.156 true 0.76,2.083 1.833,2.573 true 0.521,1.063 0.979,1.26 0.458,0.198 10 false F55 2.521,2.042 2.979,2.24 0.458,0.198 10 false BAT 0.521,1.99 0.979,2.188 0.458,0.198 10 false IG1 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Steering Angle Sensor)


Remove the steering wheel and column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the F55 steering angle sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F55-5 (BAT) - Body ground Always 11 to 14 V
F55-4 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C269831C19
0.406,1 0.854,1.323 0.448,0.323 0.76,2.083 1.281,2.583 true 0.521,1.063 0.979,1.26 0.458,0.198 10 false F55 0.458,1.979 0.917,2.177 0.458,0.198 10 false ESS 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering angle sensor, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition
F55-1 (ESS) - Body ground 1 minute after power switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)