Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3210E _59 Vehicle Exterior _047533 LIGHTING (EXT) _0244228 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights.

WIRING DIAGRAM

E338153E03
0.26,0.677 1.125,1.125 0.865,0.448 10 false from Auxiliary Battery 1.906,2.76 2.51,2.979 0.604,0.219 10 false FOG FR 1.906,0.854 2.552,1.073 0.646,0.219 10 false J/B-AM 2.958,2.906 3.563,3.125 0.604,0.219 10 false FOG FR 5.063,1.313 5.51,1.531 0.448,0.219 10 false TAIL 5.073,1.833 5.521,2.052 0.448,0.219 10 false TAIL 6.052,0.615 6.563,0.833 0.51,0.219 10 false TRLY 6.052,2.198 6.563,2.417 0.51,0.219 10 false FFGO 5.802,0.615 6.208,0.833 0.406,0.219 10 false 14 5.854,2.198 6.26,2.417 0.406,0.219 10 false 7 4.302,3.135 5.906,3.594 1.604,0.458 10 false Instrument Panel Junction Block Assembly 5.427,4.823 5.875,5.042 0.448,0.219 10 false MB 5.427,4.979 7.094,5.479 1.667,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 1.635,3.469 1.906,3.688 0.271,0.219 10 false 1 1.635,4.74 1.906,4.958 0.271,0.219 10 false 1 2.531,3.469 2.802,3.688 0.271,0.219 10 false 4 2.531,4.75 2.802,4.969 0.271,0.219 10 false 4 1.823,3.469 2.094,3.688 0.271,0.219 10 false E 1.813,4.74 2.083,4.958 0.271,0.219 10 false E 2.354,3.469 2.625,3.688 0.271,0.219 10 false B 2.344,4.75 2.615,4.969 0.271,0.219 10 false B 1.427,3.906 2.031,4.125 0.604,0.219 10 false A26 1.427,4.094 2.969,4.313 1.542,0.219 10 false Fog Light Assembly LH 1.406,5.229 2.031,5.438 0.625,0.208 10 false A25 1.406,5.385 2.948,5.604 1.542,0.219 10 false Fog Light Assembly RH 3.469,2.208 3.74,2.427 0.271,0.219 10 false 1 2.802,2.208 3.073,2.427 0.271,0.219 10 false 2 3.469,2.531 3.74,2.75 0.271,0.219 10 false 3 2.802,2.531 3.073,2.75 0.271,0.219 10 false 5 4.24,0.698 4.5,0.896 0.26,0.198 10 false 3K 4.24,1.688 4.5,1.885 0.26,0.198 10 false 3D 4.24,2.281 4.5,2.479 0.26,0.198 10 false 3A 4.281,0.5 4.552,0.719 0.271,0.219 10 false 1 4.25,1.5 4.521,1.719 0.271,0.219 10 false 11 4.25,2.094 4.521,2.313 0.271,0.219 10 false 52 1.823,3.771 3.365,3.99 1.542,0.219 10 false Fog Light 1.823,5.042 3.365,5.26 1.542,0.219 10 false Fog Light

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Fog Light Relay Front fog light relay ON/OFF Light control switch is in tail position
Body Electrical > Main Body > Active Test
Tester Display
Front Fog Light Relay
50004 123 16
OK:

Front fog light relay operates. (Front fog lights come on.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - AUXILIARY BATTERY)
3.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - AUXILIARY BATTERY)
a.

Remove the FOG FR relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FOG FR RELAY INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FOG FR RELAY INPUT VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 2 - Body ground Power switch off, Taillights on 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT FOG FR RELAY

NG

9.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.INSPECT FOG FR RELAY
a.
E222294C74
1.073,0.958 1.302,0.49 1.302,0.49 1.438,0.49 false 1.063,1.333 1.146,1.75 1.146,1.75 1.344,1.75 false 0.802,1.01 0.938,0.49 0.938,0.49 1.063,0.49 false 0.563,1.281 0.635,1.76 0.635,1.76 0.823,1.76 false 1.458,0.406 1.563,0.563 0.104,0.156 10 false 1 1.375,1.667 1.479,1.823 0.104,0.156 10 false 2 1.094,0.396 1.198,0.552 0.104,0.156 10 false 5 0.844,1.667 0.948,1.823 0.104,0.156 10 false 3 0.125,0.198 0.438,0.354 0.313,0.156 10 false *a
*a Component without harness connected
(FOG FR Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - FOG LIGHT ASSEMBLY LH AND FOG LIGHT ASSEMBLY RH)

NG

REPLACE FOG FR RELAY

6.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - FOG LIGHT ASSEMBLY LH AND FOG LIGHT ASSEMBLY RH)
a.

Disconnect the A26 fog light assembly LH connector.


b.

Disconnect the A25 fog light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A26-4 Always Below 1 Ω
Relay terminal 3 - A25-4 Always Below 1 Ω
Relay terminal 3 or A26-4 - Body ground Always 10 kΩ or higher
Relay terminal 3 or A25-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 1 - 3A-52 Always Below 1 Ω
Relay terminal 1 or 3A-52 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

E259586C26
1.146,0.302 1.469,0.49 0.323,0.188 4.604,0.302 4.958,0.51 0.354,0.208 4.104,1.438 3.833,1.052 false 1.229,0.313 1.542,0.51 0.313,0.198 10 false 3A 4.688,0.323 5,0.521 0.313,0.198 10 false MB 3.969,1.49 4.594,1.688 0.625,0.198 10 false FFGO 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-52 - MB-7 (FFGO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 2 - 3D-11 Always Below 1 Ω
Relay terminal 2 or 3D-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR