The hybrid vehicle control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction. If these DTCs are output, replace the hybrid vehicle control ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P062F46 | Hybrid/EV Powertrain Control Module EEPROM Calibration / Parameter Memory Failure | ·
ECU internal malfunction (EEPROM error) ·
The power switch is turned off when the auxiliary battery voltage is 9.5 V or less. (1 trip detection logic) |
·
Hybrid vehicle control ECU ·
Auxiliary battery |
Comes on | Master Warning Light:
Comes on |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 15 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History |
Read and record the vehicle control history (Hybrid Control).
| Result | Proceed to |
|---|---|
| Auxiliary Battery Voltage Low (HV) or Auxiliary Battery Voltage Low (Inverter) is stored. | A |
| Auxiliary Battery Voltage Low (HV) and Auxiliary Battery Voltage Low (Inverter) are not stored. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Read the freeze frame data of DTC P062F46.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
According to the display on the GTS, read the freeze frame data and make a note of the value of Total Distance Traveled.
Read the data recorded in the vehicle control history item (Auxiliary Battery Voltage Low (HV) or Auxiliary Battery Voltage Low (Inverter)) which was stored when the auxiliary battery voltage dropped below the threshold.
Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History |
According to the display on the GTS, read the data of the vehicle control history data and make a note of the value of Total Distance Traveled.
Compare the values in the freeze frame data and the vehicle control history.
| Result | Proceed to |
|---|---|
| The total distance driven is the same. | A |
| The total distance driven is not the same. | B |
Turn the power switch off.
A
B
Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.
Measure the auxiliary battery voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal | 20°C (68°F), Power switch off | 11.0 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs.
Turn the power switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 15 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Proceed to |
|---|
| P062F46 is not output. |
| P062F46 is output. |
Turn the power switch off.
P062F46 is not output.
P062F46 is output.