The battery cooling blower assembly speed is controlled by the hybrid vehicle control ECU. Power is supplied to the battery cooling blower assembly when the MREL terminal of the hybrid vehicle control ECU turns on the IGCT relay. The hybrid vehicle control ECU sends command signals (SI0) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The frequency (FP0) of the battery cooling blower assembly is sent to the hybrid vehicle control ECU via the battery voltage sensor as a monitor signal using serial communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A8111 | Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground | Both of the following conditions are met:
·
The speed calculated based on the battery cooling blower assembly output frequency is not within the target control speed range. ·
The battery cooling blower assembly speed is excessively low when a certain level of speed is requested (possibility of an open or short to ground in connected circuits, or motor locking). (1 trip detection logic) |
·
Battery voltage sensor ·
Hybrid vehicle control ECU ·
Battery cooling blower assembly ·
BATT FAN fuse ·
Wire harness or connector |
Does not come on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A8111 | ·
Hybrid Battery Cooling Fan Drive Request ·
Hybrid Battery Cooling Fan 1 Drive Status ·
Hybrid Battery Cooling Fan Frequency |
The following items can be helpful when performing repairs:
Hybrid Battery Temperature 1 to 3
BATT Voltage
"Hybrid Battery Cooling Fan Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Select fan mode 6 and operate the battery cooling blower assembly and wait for 10 seconds or more.
Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
As the battery cooling blower assembly speed is excessively low, there is a possibility of an open or short to ground in connected circuits, or motor locking.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0AFC00 or P0AFC96 is not output. | A |
| P0AFC00 or P0AFC96 is also output. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Battery cooling blower assembly operation and blower volume can be checked. | OFF, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Select air volume mode 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot be performed, skip it and proceed to the next step to check if the fan operates and air is sucked. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling blower assembly.
Check that the battery cooling blower assembly operates, air is sucked into the inlet duct and the operation sound is normal.
The battery cooling blower assembly may not stop even when turning the cooling fan off in the "Control the Hybrid Battery Cooling Fan" Active Test. This is due to HV system control and is not a malfunction.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery shield panel.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL
Disconnect the M35 battery voltage sensor connector.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL
Before disconnecting the connector, check that it is not loose or disconnected.
Disconnect the M38 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M35-8 (FP0) - M38-1 (FP0) | Power switch off | Below 1 Ω |
| M35-8 (FP0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M35-8 (FP0) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the M38 battery cooling blower assembly connector.
Reconnect the M35 battery voltage sensor connector.
Install the No. 1 HV battery shield panel.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery shield panel.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Battery cooling blower assembly operation and blower volume can be checked. | OFF, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan Frequency.
| Tester Display |
|---|
| Hybrid Battery Cooling Fan Frequency |
Select each air volume mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling fan assembly.
| *a | Component with harness connected
(Battery Voltage Sensor) |
While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.
| Tester Connection | Condition |
|---|---|
| M35-8 (FP0) - M35-5 (GND) | Battery cooling blower assembly is operating. |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Compare the values in each air volume mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current air volume mode.
| Result | Proceed to |
|---|---|
| Both of the value in the Data List (Hybrid Battery Cooling Fan Frequency) and the actual measured value at the battery voltage sensor connector are 0 Hz. | A |
| Other than above | B |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the No. 1 HV battery shield panel.
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion assembly.
Disconnect the M38 battery cooling bower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M38-1 (FP0) - M38-3 (GND0) | Power switch on (IG) | 4.5 to 5.5 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the M38 battery cooling blower assembly connector.
Install the rear seat cushion assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves and protective goggles.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery shield panel.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Battery cooling blower assembly operation and blower volume can be checked. | OFF, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Cooling Fan Frequency.
| Tester Display |
|---|
| Hybrid Battery Cooling Fan Frequency |
Select each air volume mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling blower assembly.
| *a | Component with harness connected
(Battery Voltage Sensor) |
While the cooling fan is operating, compare the value in the Data List (Hybrid Battery Cooling Fan Frequency) with the frequency value that was actually measured at the battery voltage sensor connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M35-8 (FP0) - M35-5 (GND) | Battery cooling blower assembly is operating. | Difference between the value in the Data List (Hybrid Battery Cooling Fan Frequency) and the actual measured value at the battery voltage sensor connector is 10% or less. |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Compare the values in each air volume mode 1 to 6. If the Active Test cannot be performed, compare the values only in the current air volume mode.
| Proceed to |
|---|
| OK |
| NG |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the No. 1 HV battery shield panel.
OK
NG
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
| *2 | BATT FAN Fuse |
Remove the BATT FAN fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance of the BATT FAN fuse.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| BATT FAN fuse | Power switch off | Below 1 Ω |
Install the BATT FAN fuse to the No. 1 engine room relay block and No. 1 junction block assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion assembly.
Disconnect the M38 battery cooling bower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M38-2 (IG0) - Body ground | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)
Fuse condition (before and after removing fuse(s)) (IG circuit)
Connection condition of connectors (IG circuit)
Wire harness condition (IG circuit)
Wire harness condition (GND circuit)
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the rear seat cushion assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the F2 hybrid vehicle control ECU connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Check that each connector between the hybrid vehicle control ECU and battery cooling blower assembly is not loose or disconnected.
Remove the rear seat cushion assembly.
Disconnect the M38 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
Check the terminals of the connector for deformation and corrosion.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-38 (SI0) - M38-4 (SI0) | Power switch off | Below 1 Ω |
| M38-4 (SI0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Make sure that each connector between the hybrid vehicle control ECU and battery cooling blower assembly is not loose or disconnected and its terminals are not deformed or corroded.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M38-4 (SI0) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.
As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.
Check that each connector between the hybrid vehicle control ECU and battery cooling blower assembly is not loose or disconnected.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the M38 battery cooling blower assembly connector.
Install the rear seat cushion assembly.
Reconnect the F2 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.
| Tester Display | Measurement Item | Control Range | Restrict Condition |
|---|---|---|---|
| Control the Hybrid Battery Cooling Fan | Battery cooling blower assembly operation and blower volume | OFF, 1, 2, 3, 4, 5, 6 | Intake air temperature -10°C (14°F) or higher |
| Tester Display |
|---|
| Control the Hybrid Battery Cooling Fan |
Select each air volume mode 1 to 6 in the "Control the Hybrid Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
If the Active Test cannot turn off the battery cooling blower assembly, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the hybrid vehicle control ECU sends a command to operate the battery cooling blower assembly.
Connect an oscilloscope to the F2 hybrid vehicle control ECU connector and check the waveform.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
- | - |
| Item | Content |
|---|---|
| Tester Connection | F2-38(SI0) - F2-12(E01) |
| Equipment Setting | 10 V/DIV., 1 ms./DIV. |
| Condition | Power switch on (IG), during Active Test |
Perform this inspection with the hybrid vehicle control ECU connector connected.
The wave length will vary with the operating speed of the battery cooling blower assembly.
Turn the power switch off.
| *a | Waveform 1 |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| Result | Proceed to |
|---|---|
| Normal (The pulse output of waveform 1) | A |
| No pulse generation | B |
A
B
Disconnect the F2 hybrid vehicle control ECU connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-12 (E01) - Body ground | Power switch off | Below 1 Ω |
Reconnect the F2 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F2 hybrid vehicle control ECU connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-11 (E02) - Body ground | Power switch off | Below 1 Ω |
Reconnect the F2 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the IGCT relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Check the terminals of the relay for deformation and corrosion.
Remove the rear seat cushion assembly.
Disconnect the M38 battery cooling blower assembly connector.
Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.
Before disconnecting the connector, check that it is not loose or disconnected.
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | IGCT Relay Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IGCT relay terminal 5 - M38-2 (IG0) | Power switch off | Below 1 Ω |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Check that each connector between the IGCT relay and battery cooling blower assembly is not loose or disconnected.
Reconnect the M38 battery cooling blower assembly connector.
Install the rear seat cushion assembly.
Install the IGCT relay to the No. 1 engine room relay block and No. 1 junction block assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the BATT FAN fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
Remove the rear seat cushion assembly.
Disconnect the M38 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly |
| *a | Front view of wire harness connector
(to Battery Cooling Blower Assembly) |
| *b | BATT FAN Fuse Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M38-2 (IG0) - Terminals other than 2 (BATT FAN fuse) and body ground | Power switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the M38 battery cooling blower assembly connector.
Install the rear seat cushion assembly.
Install the BATT FAN fuse to the No. 1 engine room relay block and No. 1 junction block assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear seat cushion assembly.
Disconnect the M38 battery cooling blower assembly connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Component without harness connected
(Battery Cooling Blower Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M38-2 (IG0) - M38-3 (GND0) and Body ground | Power switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Reconnect the M38 battery cooling blower assembly connector.
Install the rear seat cushion assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT