Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) › from 2016.08
RM3210E _58 Vehicle Interior _047538 SEAT BELT _0244926 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) G

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the power switch on (IG).


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


c.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


d.

Turn the power switch on (READY).


e.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


f.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 2.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and allow it to come into contact with the seatback.



b.

Fasten the driver seat belt.


c.

Turn the power switch on (IG).


d.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


e.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


f.

Turn the power switch on (READY).


g.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


h.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 3.INSPECT REAR SEAT BELT WARNING LIGHT

a.
B353656C01
0.917,1.75 0.917,1.333 false 1.719,1.75 1.719,1.385 false 2.51,1.75 2.51,1.333 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *1 0.844,1.781 1.094,1.948 0.25,0.167 10 false *a 1.646,1.781 1.896,1.948 0.25,0.167 10 false *b 2.448,1.781 2.698,1.948 0.25,0.167 10 false *c
*1 Rear Seat Belt Warning Light (Combination Meter Assembly)
*a LH
*b Center
*c RH


Check the state of the rear seat belt warning light on the combination meter assembly:

i.

Turn the Power switch off.


ii.

Open and then close either rear door.


iii.

Turn the power switch on (IG).


iv.

When a rear seat belt is not fastened, check that the rear seat belt warning light on the combination meter assembly is illuminated.


v.

After 34 seconds, check that the rear seat belt warning light on the combination meter assembly turns off.


vi.

When one of the rear seat belts is unfastened from being fastened, check that the rear seat belt warning light on the combination meter assembly illuminates.



Hide 4.INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)>CUSTOMIZE PARAMETERS


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and allow it to come into contact with the seatback.



b.

Lift the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


c.

Turn the power switch on (READY).


d.

Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.


e.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.


f.

Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.


g.

After the buzzer has stopped, turn the power switch off and then start the hybrid control system again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver, front passenger or a rear seat belt is not fastened, and check that the buzzer sounds again.


h.

After the buzzer has stopped, fasten the driver, front passenger or rear seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more, unfasten the driver, front passenger or a rear seat belt and check that the buzzer sounds again.


i.

After the buzzer has stopped, stop the vehicle, change the shift state to reverse (R) and then select drive (D). Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.