Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) › from 2016.08
RM3210E _58 Vehicle Interior _047538 SEAT BELT _0244926 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) U

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B434104N16
3.531,3.198 3.896,3.417 0.365,0.219 1.396,4.583 1.76,4.802 0.365,0.219 3.729,4.583 4.094,4.802 0.365,0.219 5.313,4.583 5.677,4.802 0.365,0.219 6.302,4.552 6.667,4.771 0.365,0.219 1.583,6.24 1.948,6.458 0.365,0.219 4.813,6.26 5.177,6.479 0.365,0.219 3.354,7.854 3.719,8.073 0.365,0.219 1.667,1.333 1.906,1.333 false 4,0.813 4,0.365 4,0.365 4.125,0.365 false 0.865,1.094 1.177,1.292 0.313,0.198 10 false 3H 0.865,1.646 1.177,1.844 0.313,0.198 10 false 3F 0.875,2.01 1.188,2.208 0.313,0.198 10 false 3L 0.885,2.24 1.198,2.438 0.313,0.198 10 false 3K 1.969,1.26 2.281,1.458 0.313,0.198 10 false F17 4.188,0.292 4.5,0.49 0.313,0.198 10 false MB 5.844,1.104 6.156,1.302 0.313,0.198 10 false 3D 5.844,1.76 6.156,1.958 0.313,0.198 10 false 3A 3.594,3.219 3.906,3.417 0.313,0.198 10 false F17 1.5,4.604 1.813,4.802 0.313,0.198 10 false 3H 3.823,4.604 4.135,4.802 0.313,0.198 10 false 3F 5.427,4.604 5.74,4.802 0.313,0.198 10 false 3L 6.396,4.583 6.708,4.781 0.313,0.198 10 false 3K 1.688,6.26 2,6.458 0.313,0.198 10 false 3D 4.917,6.292 5.229,6.49 0.313,0.198 10 false 3A 3.438,7.875 3.75,8.073 0.313,0.198 10 false MB

a.

Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Power switch on (IG) → off 11 to 14 V → Below 1 V
MB-30 (ACC) - Body ground - Ignition power supply (ACC signal) Power switch on (ACC) → off 11 to 14 V → Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-2 (RCTY) - Body ground - Rear door courtesy light switch RH input Rear door LH closed (OFF) 10 kΩ or higher
Rear door LH open (ON) Below 1 Ω
MB-13 (LCTY) - Body ground - Rear door courtesy light switch LH input Rear door RH closed (OFF) 10 kΩ or higher
Rear door RH open (ON) Below 1 Ω



CHECK COMBINATION METER ASSEMBLY


B345456N08
3.427,0.208 3.813,0.427 0.385,0.219 3.552,0.229 3.865,0.427 0.313,0.198 10 false F6

a.

Disconnect the F6 combination meter assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F6-22 (B) - Body ground W - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
F6-21 (IG+) - Body ground G - Body ground Ignition power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
F6-28 (ES) - Body ground W-B - Body ground Ground Always Below 1 Ω
F6-12 (RLSB) - Body ground GR - Body ground Rear LH seat belt buckle switch signal Rear LH seat belt fastened 10 kΩ or higher
Rear LH seat belt unfastened Below 1 Ω
F6-11 (RCSB) - Body ground R - Body ground Rear center seat belt buckle switch signal Rear center seat belt fastened 10 kΩ or higher
Rear center seat belt unfastened Below 1 Ω
F6-10 (RRSB) - Body ground P - Body ground Rear RH seat belt buckle switch signal Rear RH seat belt fastened 10 kΩ or higher
Rear RH seat belt unfastened Below 1 Ω



CHECK AIRBAG ECU ASSEMBLY


C147673N81
1.938,0.115 2.313,0.333 0.375,0.219 5.073,0.094 5.448,0.323 0.375,0.229 3.385,0.104 3.76,0.323 0.375,0.219 2.052,0.135 2.365,0.344 0.313,0.208 10 false M1 5.146,0.125 5.448,0.313 0.302,0.188 10 false M45 3.479,0.125 3.792,0.333 0.313,0.208 10 false F56

Terminal No. Terminal Symbol Destination
M1-10 LBE+ Front seat inner belt assembly LH
M1-18 LBE- Front seat inner belt assembly LH


CHECK OCCUPANT DETECTION ECU


C238368N24
4.25,0.083 4.646,0.323 0.396,0.24 2.604,0.073 3,0.313 0.396,0.24 2.729,0.104 3.198,0.438 0.469,0.333 10 false a7 4.354,0.125 4.76,0.313 0.406,0.188 10 false a8

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a8-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 V
a8-6 (IG2) - a8-10 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
a8-9 (BGND) - a8-10 (GND) P - W-B Front passenger buckle switch ground Always Below 1 V
a8-7 (BSW) - a8-9 (BGND) G - P Front passenger buckle switch signal Always Pulse generation
a7-1 (SVC1) - a7-5 (SGD1) R - G Front occupant classification sensor LH power supply Power switch on (IG) 11 to 14 V
a7-2 (SVC3) - a7-6 (SGD3) GR - W Rear occupant classification sensor LH power supply Power switch on (IG) 11 to 14 V
a7-3 (SIG1) - a7-5 (SGD1) P - G Front occupant classification sensor LH signal Power switch on (IG) Pulse generation
a7-4 (SIG3) - a7-6 (SGD3) SB - W Rear occupant classification sensor LH signal Power switch on (IG) Pulse generation
a7-5 (SGD1) - a8-10 (GND) G - W-B Front occupant classification sensor LH ground Always Below 1 V
a7-6 (SGD3) - a8-10 (GND) W - W-B Rear occupant classification sensor LH ground Always Below 1 V