Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3210E _56 Audio / Visual / Telematics _057161 TELEMATICS _0287335 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1570  Red LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the power switch is turned on (IG).

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1570 Red LED Error Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 20 seconds when the power switch is on (IG).
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Wire harness or connector



WIRING DIAGRAM

E342832E16
1.896,1.021 2.354,1.219 0.458,0.198 10 false RED 3.396,0.656 3.656,0.885 0.26,0.229 10 false 10 3.406,1.073 3.563,1.271 0.156,0.198 10 false 8 3,0.656 3.615,0.854 0.615,0.198 10 false IND1 2.938,1.073 3.552,1.271 0.615,0.198 10 false GND3 1.24,1.729 1.698,1.927 0.458,0.198 10 false O6 1.24,1.906 3.958,2.135 2.719,0.229 10 false Map Light Assembly (Manual (SOS) Switch) 4.938,0.667 5.25,0.865 0.313,0.198 10 false 11 4.927,1.073 5.24,1.271 0.313,0.198 10 false 26 5.167,0.781 5.781,0.979 0.615,0.198 10 false IND1 5.167,1.073 5.781,1.271 0.615,0.198 10 false SIG- 5.104,1.729 5.563,1.927 0.458,0.198 10 false F36 5.104,1.917 6.667,2.125 1.563,0.208 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


HINT:

If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
a.
E221774C16
1.958,1.938 2.458,2.531 false 1.094,2.552 1.615,1.948 false 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.906,2.594 1.323,2.823 0.417,0.229 10 false IND1 2.333,2.583 2.75,2.813 0.417,0.229 10 false GND3
*a Component with harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
10 (IND1) - 8 (GND3) 2 seconds after power switch turned on (IG)
→ Power switch off
8.5 to 10 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
a.
E221773C10
2.188,1.75 1.969,1.365 false 1.448,1.74 1.635,1.344 false 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.292,1.771 1.729,1.927 0.438,0.156 10 false IND1 2.073,1.771 2.552,1.948 0.479,0.177 10 false GND3
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 10 (IND1) and a negative (-) lead to terminal 8 (GND3) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch indicator (red) illuminates.

OK:

Manual (SOS) switch indicator (red) illuminates.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F36 telematics transceiver connector.


b.

Disconnect the O6 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F36-11 (IND1) - O6-10 (IND1) Always Below 1 Ω
F36-11 (IND1) or O6-10 (IND1) - Body ground Always 10 kΩ or higher
F36-26 (SIG-) - O6-8 (GND3) Always Below 1 Ω
F36-26 (SIG-) or O6-8 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT