Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.08
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B1532  LVDS Signal Malfunction (from Extension Module)  


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected via LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1532 LVDS Signal Malfunction (from Extension Module) When any of the following conditions is met:
·

Video signal (digital) is lost.

·

Navigation ECU is/was not connected while the power switch is/was on (ACC) or on (IG).

·

Communication between the master unit and the navigation ECU is/was not possible when the engine is/was started.


·

Navigation ECU power source circuit

·

LVDS circuit between radio and display receiver assembly and navigation ECU

·

Navigation ECU

·

Radio and display receiver assembly

·

Harness and connector



HINT:
·

Even if no malfunction is present, this DTC may be stored depending on the auxiliary battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E276665E35
0.688,2.333 2.448,2.75 1.76,0.417 10 false Radio and Display Receiver Assembly 5.208,2.333 6.323,2.542 1.115,0.208 10 false Navigation ECU 2.219,1.896 2.448,2.083 0.229,0.188 10 false e1 4.844,1.885 5.073,2.073 0.229,0.188 10 false e4 2.229,0.708 2.458,0.896 0.229,0.188 10 false e2 2.229,1.104 2.458,1.292 0.229,0.188 10 false e2 2.229,1.5 2.458,1.688 0.229,0.188 10 false e2 2.271,0.51 2.5,0.698 0.229,0.188 10 false 4 2.26,0.917 2.49,1.104 0.229,0.188 10 false 3 2.26,1.313 2.49,1.5 0.229,0.188 10 false 8 2.26,1.708 2.49,1.896 0.229,0.188 10 false 1 4.844,0.708 5.073,0.896 0.229,0.188 10 false e3 4.844,1.094 5.073,1.281 0.229,0.188 10 false e3 4.844,1.5 5.073,1.688 0.229,0.188 10 false e3 4.865,0.51 5.094,0.698 0.229,0.188 10 false 1 4.865,0.917 5.094,1.104 0.229,0.188 10 false 3 4.865,1.313 5.094,1.5 0.229,0.188 10 false 2 4.854,1.708 5.083,1.896 0.229,0.188 10 false 1 1.781,0.708 2.083,0.927 0.302,0.219 10 false +B2 5.146,0.708 5.448,0.927 0.302,0.219 10 false B+ 1.708,1.094 2.115,1.292 0.406,0.198 10 false ACC2 5.146,1.104 5.552,1.302 0.406,0.198 10 false ACC 1.708,1.49 2.115,1.688 0.406,0.198 10 false GND2 5.146,1.49 5.552,1.688 0.406,0.198 10 false GND 1.698,1.885 2.104,2.083 0.406,0.198 10 false LVDS 5.146,1.896 5.552,2.094 0.406,0.198 10 false LVDS 2.979,2.865 4.74,3.052 1.76,0.188 10 false : LVDS Communication Line

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU POWER SOURCE)
a.

Disconnect the e3 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e3-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e3-1 (B+) - e3-2 (GND) Power switch off 11 to 14 V
e3-3 (ACC) - e3-2 (GND) Power switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.REPLACE HARNESS AND CONNECTOR (LVDS COMMUNICATION LINE)

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
2.REPLACE HARNESS AND CONNECTOR (LVDS COMMUNICATION LINE)
a.

Replace the harness and connector (LVDS communication line) with a new or known good one.


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

3.REPLACE NAVIGATION ECU
3.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the e2 radio and display receiver assembly connector.


b.

Disconnect the e3 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e2-4 (+B2) - e3-1 (B+) Always Below 1 Ω
e2-3 (ACC2) - e3-3 (ACC) Always Below 1 Ω
e2-8 (GND2) - e3-2 (GND) Always Below 1 Ω
e2-4 (+B2) or e3-1 (B+) - Body ground Always 10 kΩ or higher
e2-3 (ACC2) or e3-3 (ACC) - Body ground Always 10 kΩ or higher
e2-8 (GND2) or e3-2 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR