2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2007


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. The "DISCHARGE FUEL SYSTEM PRESSURE" procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the "DISCHARGE FUEL SYSTEM PRESSURE" procedures, pressure will remain in the fuel lines. When disconnecting a fuel line, cover it with a shop rag or a piece of cloth to prevent fuel from spraying or coming out.

  1. A128750E01
    Remove the console box (Click here).

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171/P0172 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. A128750E01
    Connect the connector.

  1. Install the console box (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE ENGINE ASSEMBLY
  1. Remove the engine from the vehicle (Click here).


4. INSTALL ENGINE TO STAND
  1. Install the engine to an engine stand. Remove the sling device and chain block from the engine.


5. REMOVE NO. 2 OIL DIPSTICK GUIDE
  1. Remove the oil dipstick.

  1. A132179
    Remove the bolt and dipstick guide.


6. REMOVE OIL DIPSTICK GUIDE

  1. A132180
    Remove the bolt and dipstick guide.


7. REMOVE OIL FILTER CAP ASSEMBLY

  1. A132053E01
    Connect the hose to a pipe.

    HINT:
    The drain pipe is supplied with the oil filter element.

  1. A131922
    Remove the oil filter drain plug and O-ring, insert the drain pipe into the oil filter cap, and drain the engine oil into a container.

  1. A131923
    Make sure that oil is completely drained, and remove the pipe and O-ring.

    HINT:
    Be sure to turn the pipe in the direction indicated by the arrow to remove it.

  1. A131924E01
    Using SST, remove the oil filter cap together with the oil filter element.
    SST
    09228-06501  


8. REMOVE OIL FILTER ELEMENT

  1. A115233E05
    Remove the oil filter element and 2 O-rings from the oil filter cap.

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.


9. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A132107
    Remove the 16 bolts and 2 nuts.

  1. A132161
    Insert the blade of an oil pan seal cutter between the oil pans, cut through the applied sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


10. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A132108
    Remove the bolt, 2 nuts, oil strainer and gasket.


11. REMOVE OIL PAN SUB-ASSEMBLY

  1. A132109
    Remove the 16 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

  1. A132110
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A132111
    Remove the 2 O-rings from the oil pump.


12. REMOVE WATER INLET HOUSING

  1. A132393
    Remove the 2 nuts and remove the water inlet from the water inlet housing.


13. REMOVE OIL PIPE

  1. A134878E01
    Remove the bolt.

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.


14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A132119
    Remove the 12 bolts, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same locations they were removed from.


15. REMOVE NO. 1 OIL PIPE

  1. A135726E01
    Remove the 2 oil pipe unions, gaskets and oil pipe.

  1. Remove the oil control valve filter LH and gaskets.


16. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A132120
    Remove the 12 bolts, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same locations they were removed from.


17. REMOVE CRANKSHAFT PULLEY

  1. A132066E01
    Using SST, loosen the crankshaft pulley set bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

  1. A132067E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


18. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A132150
    Remove the 23 bolts and 2 nuts as shown in the illustration.

  1. A132099
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A132100
    Remove the gasket.

← COMPONENTS (from Aug 2007)DISASSEMBLY (from Aug 2007) →