DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the intelligent tester, read the "Data List".
ABS/VSC/TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light / ON or OFF
ON: ABS warning light on
OFF: ABS warning light off
-
VSC Warning Light
VSC warning light / ON or OFF
ON: VSC warning light on
OFF: VSC warning light off
-
Brake Warning Light
Brake warning light / ON or OFF
ON: Brake warning light on
OFF: Brake warning light off
-
Slip Indicator Light
Slip indicator light / ON or OFF
ON: Slip indicator light on
OFF: Slip indicator light off
-
Downhill Assist Control Light*9
Downhill assist control indicator light / ON or OFF
ON: Downhill assist control switch on
OFF: Downhill assist control switch off
-
Auto LSD Indicator Light
AUTO LSD indicator light / ON or OFF
ON: Traction control switch (VSC OFF switch) on
OFF: Traction control switch (VSC OFF switch) off
-
Buzzer
Skid control buzzer / ON or OFF
ON: Buzzer on
OFF: Buzzer off
-
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Main Idle SW
Main idle switch / ON or OFF
ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Brake Pedal Load Sensing SW*10
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-
Gear Position
Gear position information / P,N, R, 1st-5th, FAIL, NOT R
Actual gear position
-
Shift Lever Position
Shift lever position information / P,N, R, D/M, 1st-6th/B, FAIL
Actual shift lever position
-
Shift Information
Shift information / ON or OFF
ON: During gear change
-
Inspection Mode
Inspection mode / OTHER or INSPECT
OTHER: Normal mode
INSPECT: Inspection mode
-
Number of IG ON (Inspection)
Number of ignition switch ON operations after entering the inspection mode / min.: 0, max.: 255
Min.: 0
Max.: 255
-
Auto LSD Switch
Traction control switch (VSC OFF switch) / ON or OFF
ON: Traction control switch (VSC OFF switch) on
OFF: Traction control switch (VSC OFF switch) off
-
Downhill Assist Control Switch*9
Downhill assist control switch / ON or OFF
ON: Downhill assist control switch on
OFF: Downhill assist control switch off
-
Master Cylinder Sensor
Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V
When brake pedal released: 0.3 to 0.9 V
Reading increases when the brake pedal depressed.
Zero Point of M/C
Memorized zero point value of master cylinder pressure sensor / min.: -12.5 MPa, max.: 12.4 MPa
Min.: -12.5 MPa
Max.: 12.4 MPa
-
Deceleration Sensor
Deceleration sensor 1 reading / min.: -18.52 m/s2, max.: 18.39 m/s2
Min.: -18.52 m/s2
Max.: 18.39 m/s2
Reading changes when vehicle is bounced.
Zero Point of Decele
Memorized zero point value of deceleration sensor 1 / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Deceleration Sensor 2
Deceleration sensor 2 reading / min.: -18.52 m/s2, max.: 18.39 m/s2
Min.: -18.52 m/s2
Max.: 18.39 m/s2
Reading changes when vehicle is bounced.
Zero Point of Decele 2
Memorized zero point value of deceleration sensor 2 / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Yaw Rate Sensor
Yaw rate sensor 1 reading / min.: -128 deg/s, max.: 127 deg/s
Vehicle stationary: 0 deg/s
Right turn: -128 to 0 deg/s
Left turn: 0 to 127 deg/s
-
Zero Point of Yaw Rate
Memorized zero point value of yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s
Min.: -128 deg/s
Max.: 127 deg/s
-
Zero Point of Yaw Rate 2
Memorized zero point value of yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s
Min.: -128 deg/s
Max.: 127 deg/s
-
Steering Angle Sensor
Steering angle sensor reading / min.: -3276.8 deg, max.: 3276.7 deg
Left turn: Increase
Right turn: Decrease
-
Zero Point of Steering Angle
Memorized zero point value of steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg
Min.: -3276.8 deg
Max.: 3276.7 deg
-
Lateral G
Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Forward and Rearward G
Forward and rearward G / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Yaw Rate Value
Yaw rate value / min.: -128 deg/s, max.: 127 deg/s
Min.: -128 deg/s
Max.: 127 deg/s
-
Steering Angle Value
Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg
Min.: -3276.8 deg
Max.: 3276.7 deg
-
FR Wheel Speed
FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer
FL Wheel Speed
FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer
RR Wheel Speed
RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer
RL Wheel Speed
RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer
Vehicle Speed
Maximum speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph)
Actual wheel speed
Similar to speed indicated on the speedometer
FR Wheel Acceleration
FR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
Min.: -200.84 m/s2
Max.: 199.27 m/s2
-
FL Wheel Acceleration
FL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
Min.: -200.84 m/s2
Max.: 199.27 m/s2
-
RR Wheel Acceleration
RR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
Min.: -200.84 m/s2
Max.: 199.27 m/s2
-
RL Wheel Acceleration
RL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
Min.: -200.84 m/s2
Max.: 199.27 m/s2
-
FR Wheel ABS Ctrl Status
FR wheel ABS control status / ON or OFF
ON: During control
-
FL Wheel ABS Ctrl Status
FL wheel ABS control status / ON or OFF
ON: During control
-
RR Wheel ABS Ctrl Status
RR wheel ABS control status / ON or OFF
ON: During control
-
RL Wheel ABS Ctrl Status
RL wheel ABS control status / ON or OFF
ON: During control
-
RR Wheel EBD Ctrl Status
RR wheel EBD control status / ON or OFF
ON: During control
-
RL Wheel EBD Ctrl Status
RL wheel EBD control status / ON or OFF
ON: During control
-
BA Ctrl Status
BA control status / ON or OFF
ON: During control
-
TRC (TRAC) Ctrl Status
TRC control status / ON or OFF
ON: During control
-
TRC (TRAC) Engine Ctrl Status
TRC engine control status / ON or OFF
ON: During control
-
TRC (TRAC) Brake Ctrl Status
TRC brake control status / ON or OFF
ON: During control
-
FR Wheel VSC Ctrl Status
FR wheel VSC control status / ON or OFF
ON: During control
-
FL Wheel VSC Ctrl Status
FL wheel VSC control status / ON or OFF
ON: During control
-
RR Wheel VSC Ctrl Status
RR wheel VSC control status / ON or OFF
ON: During control
-
RL Wheel VSC Ctrl Status
RL wheel VSC control status / ON or OFF
ON: During control
-
Engine Revolutions
Engine speed / min.: 0 r/min, max.: 65535 r/min
Min.: 0 r/min
Max.: 65535 r/min
-
Real Engine Torque
Real engine torque / min.: -1024 Nm, max.: 1023 Nm
Min.: -1024 Nm
Max.: 1023 Nm
-
Accelerator Opening Angle %
Percentage of accelerator pedal opening angle / min.: 0%, max.: 128%
Min.: 0%
Max.: 128%
-
Solenoid Relay
Solenoid relay / ON or OFF
ON: Solenoid relay on
OFF: Solenoid relay off
-
Electronically Controlled Brake system Motor Relay
Electronically Controlled Brake system motor relay / ON or OFF
ON: Motor relay on
OFF: Motor relay off
-
Fail Safe Motor Relay
Fail-safe motor relay / ON or OFF
ON: Motor relay on
OFF: Motor relay off
-
TR(A)C / VSC Solenoid (SM2)
TRC / VSC solenoid (SM2) / ON or OFF
ON: Operates
-
TR(A)C / VSC Solenoid (SM1)
TRC / VSC solenoid (SM1) / ON or OFF
ON: Operates
-
ABS Solenoid (SFRH)*1
ABS solenoid (SFRH) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SFRR)*2
ABS solenoid (SFRR) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SFLH)*3
ABS solenoid (SFLH) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SFLR)*4
ABS solenoid (SFLR) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SRRH)*5
ABS solenoid (SRRH) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SRRR)*6
ABS solenoid (SRRR) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SRLH)*7
ABS solenoid (SRLH) / ON or OFF
ON: Operates
OFF: Does not operate
-
ABS Solenoid (SFLR)*8
ABS solenoid (SRLR) / ON or OFF
ON: Operates
OFF: Does not operate
-
FR Speed Open
FR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
FL Speed Open
FL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RR Speed Open
RR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RL Speed Open
RL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
EFI Communication Open
EFI communication open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Yaw Rate Open
Yaw rate sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Deceleration Open
Deceleration sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Steering Open
Steering angle sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Master Cylinder Open
Master cylinder pressure sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Number of DTC
Number of recorded DTCs/ min.: 0, max.: 255
Min.: 0
Max.: 255
-
- HINT:
- *1: SFRH (S: Solenoid, F: Front, R: Right, H: Holding)
- *2: SFRR (S: Solenoid, F: Front, R: Right, R: Reduction)
- *3: SFLH (S: Solenoid, F: Front, L: Left, H: Holding)
- *4: SFLR (S: Solenoid, F: Front, L: Left, R: Reduction)
- *5: SRRH (S: Solenoid, R: Rear, R: Right, H: Holding)
- *6: SRRR (S: Solenoid, R: Rear, R: Right, R: Reduction)
- *7: SRLH (S: Solenoid, R: Rear, L: Left, H: Holding)
- *8: SRLR (S: Solenoid, R: Rear, L: Left, R: Reduction)
- *9: w/ Downhill Assist Control
- *10: w/ Booster Failure Compensation
- *1: SFRH (S: Solenoid, F: Front, R: Right, H: Holding)
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the intelligent tester, perform the Active Test.
- HINT:
- The ignition switch must be turned to ON to proceed to the Active Test using the intelligent tester.
- The Active Tests of the ABS solenoid, ABS motor relay, ABS warning light and brake warning light are available when the vehicle is stopped.
- The motors stop automatically after 5 seconds of activation to prevent them from being damaged. When the motors are driven repeatedly, certain intervals are required.
- Each solenoid stops automatically after 2 seconds of activation to prevent them from being damaged, and can be operated again after a certain interval.
- Do not depress the brake pedal while only the pressure reduction solenoid valves are on.
- Do not drive 2 or more solenoids simultaneously except to operate the pressure holding solenoid valves and pressure reduction solenoid valves of each wheel.
- The ignition switch must be turned to ON to proceed to the Active Test using the intelligent tester.
ABS/VSC/TRC: Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warming light ON/OFF
Observe the combination meter.
VSC Warning Light
VSC OFF indicator light
Indicator light ON/OFF
Observe the combination meter.
Brake Warning Light
Brake warning light
Warming light ON/OFF
Observe the combination meter.
Slip Indicator Light
Slip indicator light
Indicator light ON/OFF
Observe the combination meter.
Downhill Assist Control Indicator Light*1
Downhill assist control indicator light
Indicator light ON/OFF
Observe the combination meter.
Auto LSD Indicator Light*2
AUTO LSD indicator light
Indicator light ON/OFF
Observe the combination meter.
Buzzer
Skid control buzzer
Buzzer ON/OFF
Buzzer can be heard.
Solenoid Relay
Solenoid relay
Relay ON/OFF
-
Motor Relay
Motor relay
Relay ON/OFF
Operation sound of the motor can be heard.
Stop Light Relay
Stop light control relay (BRK)
Relay ON/OFF
Observe the stop lights.
ABS Solenoid (SRLR)
ABS solenoid (SRLR)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRLH)
ABS solenoid (SRLH)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRR)
ABS solenoid (SRRR)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRH)
ABS solenoid (SRRH)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLR)
ABS solenoid (SFLR)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLH)
ABS solenoid (SFLH)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRR)
ABS solenoid (SFRR)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRH)
ABS solenoid (SFRH)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMR)
VSC/TRC solenoid (SMR)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMF)
VSC/TRC solenoid (SMF)
Solenoid ON/OFF
Operation sound of the solenoid (clicking sound) can be heard.
- HINT:
- *1: w/ Downhill Assist Control
- *2: for 2WD