FREEZE FRAME DATA
Troubleshooting · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
| FREEZE FRAME DATA |
- HINT:
- Whenever a DTC is stored or the brake system operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.
- The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the brake system was activated. However, if the vehicle was stationary or running at a low speed (7 km/h [4.3 mph] or less), or if a DTC is stored, the skid control ECU stops counting.
- Freeze frame data at the time the brake system operates:
The skid control ECU stores and updates the data whenever the brake system operates.
When the ECU stores data at the time a DTC is stored, the data stored when the brake system operated is cleared.
- Freeze frame data at the time a DTC is stored:
When the skid control ECU stores data at the time a DTC is stored, no updates will be performed until the data is cleared.
- Whenever a DTC is stored or the brake system operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.
Turn the ignition switch off and connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
From the display on the intelligent tester, select the Freeze Frame Data.
*: w/ Booster Failure CompensationABS/VSC/TRC: Tester Display
Measurement Item
Reference Value
Elapsed Time after Freeze Trigger
Elapsed time after freeze frame data recorded
Min.: 0 ms
Max.: 500 ms
Number of IG ON
Number of ignition switch ON operations since freeze frame data stored
1 to 31
Buzzer
Skid control buzzer signal
ON: Skid control buzzer on
OFF: Skid control buzzer off
Stop Light SW
Stop light switch signal
ON: Stop light switch on
OFF: Stop light switch off
Parking Brake SW
Parking brake switch signal
ON: Parking brake switch on
OFF: Parking brake switch off
Gear Position
Gear position information
FAIL
1st
2nd
3rd
4th
5th
P, N
R
NOT R
Shift Lever Position
Shift lever position information
FAIL
1st
2nd
3rd
4th
5th
6th/B
D/M
P, N
R
Operated System
Operated system status
ABS: ABS activated
VSC: VSC activated
TRC: TRC activated
BA: BA activated
HAB: HAB activated
FAIL: Fail-safe mode activated
PB: PB activated
HA-CTRL: Hill-start assist control activated
SYS: System prohibited
NON: No system activated
Master Cylinder Sensor
Master cylinder pressure sensor reading
Brake pedal released: 0.3 V to 0.9 V
Brake pedal depressed: 0.8 V to 4.5 V
M/C Sensor Grade
Master cylinder pressure sensor grade
Min.: -30 MPa/s
Max.: 225 MPa/s
Yaw Rate Sensor
Yaw rate sensor reading
Min.: -128 deg/s
Max.: 127 deg/s
Lateral G
Lateral G
Min.: -25.11 m/s2
Max.: 24.91 m/s2
Forward and Rearward G
Forward and backward G
Min.: -25.11 m/s2
Max.: 24.91 m/s2
FR Wheel Speed
FR wheel speed
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
FL Wheel Speed
FL wheel speed
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
RR Wheel Speed
RR wheel speed
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
RL Wheel Speed
RL wheel speed
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Vehicle Speed
Vehicle speed
Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202.8 mph)
Vehicle Speed Grade
Vehicle speed grade
Min.: -25.11 m/s2
Max.: 24.91 m/s2
Real Engine Torque
Real engine torque
Min.: -1024 Nm
Max.: 1023 Nm
Accelerator Opening Angle %
Accelerator pedal opening angle %
Min.: 0%
Max.: 128%
Brake Pedal
Load Sensing SW*
Brake pedal load sensing switch signal
ON: Brake pedal depressed
OFF: Brake pedal released
Inspection Mode
Inspection mode
OTHER: Normal mode
INSPECT: Inspection mode
Steering Angle Sensor
Steering angle sensor reading
Left turn: Increase
Right turn: Decrease