2005-2008 RAV4 · Service Manual BRAKE

TEST MODE PROCEDURE

Troubleshooting · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008

HINT:
  1. By switching the skid control ECU from normal mode to test mode, abnormality detection sensitivity is enhanced and troubleshooting can be conducted efficiently.
  2. Perform a sensor check in test mode after the speed sensor or sensor rotor has been repaired or replaced.
  3. If the ignition switch is turned from on to ACC or off during test mode, DTCs related to the signal check function will be erased.
  4. During test mode, the skid control ECU stores all DTCs related to the signal check function, and the DTCs are erased if normality is confirmed. Any remaining DTCs are those indicating abnormalities that were found.


CHECK SENSOR SIGNAL BY TEST MODE (When Using Intelligent Tester)

  1. Procedures for test mode:

    1. Turn the ignition switch off.

    2. Check that the steering wheel is in the centered position.

    3. A/T: Check that the shift lever is in the P position and apply the parking brake.

    4. M/T: Check that the shift lever is in neutral and apply the parking brake.

    5. B127990E01
      Connect the intelligent tester to the DLC3.

    6. Turn the ignition switch on (IG).

    7. Turn the tester on.

    8. C106672
      Set the intelligent tester to Test Mode (select "Signal Check").

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    9. C135910E01
      w/o Multi-information display:
      Check that the ABS warning light and VSC warning light blink as shown in the illustration.

    10. w/ Multi-information display:
      Check that the ABS warning light and master caution indicator light blink and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.

      HINT:
      If the ABS warning light and VSC warning warning light and multi-information display and master caution indicator light do not blink, check the TS and CG terminal circuit, and ABS and VSC warning light circuits.
      Section Title
      See procedure
      ABS Warning Light does not Come ON
      Click here
      VSC Warning Light does not Come ON
      Click here
      TS and CG Terminal Circuit
      Click here

    11. Start the engine.

  2. w/ 16-inch disc:
    Check the lost booster pressure judgment and perform the master cylinder pressure sensor zero point calibration.

    NOTICE:
    Preform the check in the lost booster pressure state (negative pressure in the booster is depressurized).


    1. Turn the ignition switch on (IG).

    2. Check that the brake warning light comes on when depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more. (The lost booster pressure state is judged normal.)

    3. Start the engine depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more.

    4. Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged normal.)

    5. Leave the vehicle for 1 second or more. (Master cylinder pressure sensor zero point calibration.)

      NOTICE:
      1. If you slowly depress the brake pedal or depress it again, master cylinder pressure sensor zero point calibration is not performed normally.
      1. If the lost booster pressure judgment check is not completed normally, the master cylinder pressure sensor check is not judged.
      1. If a recheck is performed after the engine has started, end the Test Mode, enter Test Mode again, and release the vacuum in the booster by pumping the brake pedal prior to the recheck.

  3. Check the deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 1 second or more.

      HINT:
      The deceleration sensor check can be performed together with the following master cylinder pressure sensor check.

  4. Check the master cylinder pressure sensor.

    1. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
      Check that the ABS warning light remains illuminated for 3 seconds.

      HINT:
      1. Ensure that the ABS warning light comes on.
      2. While the ABS warning light remains illuminated, continue depressing the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
      3. The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.

  5. Check the speed sensor.

    1. C108848E01
      Check that the ABS warning light is blinking as shown in the illustration.

    2. Check the speed sensor signal.

      1. Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds.
      2. Check that the ABS warning light goes off.

        NOTICE:
        1. The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
        2. If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
        3. The ABS warning light comes on immediately when an abnormality is detected.
        4. When the speed sensor signal is normal, the ABS warning light goes off while driving at 45 km/h (28 mph) or more, and blinks in the test mode pattern while the vehicle is stationary.

        5. Do not drive the vehicle at a speed of 80 km/h (50 mph) or more after the ABS warning light turns off, because test mode DTCs are set again when the vehicle speed exceeds 80 km/h (50 mph).

          C115115E04

      3. Stop the vehicle.

  6. Check the yaw rate sensor.

    1. C135910E01
      w/o Multi-information display:
      Check that the VSC warning light is blinking as shown in the illustration.

    2. w/ Multi-information display:
      Check that the master caution indicator light blinks and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.

    3. Keep the vehicle stationary on a level surface for 1 second or more.

    4. F002135E15
      Shift the shift lever to the D position (A/T) and drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more to turn the vehicle through 180°.

    5. A/T: Stop the vehicle, move the shift lever into the P position, and then apply the parking brake.

    6. M/T: Stop the vehicle, move the shift lever into neutral, and then apply the parking brake.

    7. Check that the skid control buzzer sounds for 3 seconds.

      HINT:
      1. If the skid control buzzer sounds, the signal check has been completed normally.
      2. If the skid control buzzer does not sound, check the skid control buzzer circuit (Click here).
      3. If the skid control buzzer still does not sound, there is a malfunction in the yaw rate sensor, so check for DTCs.
      4. Drive the vehicle in a 180° semi circle. At the end of the turn, the direction of the vehicle should be within 180 +-5° of its start position.
      5. Complete the vehicle turn within 20 seconds.
      6. Do not spin the wheels.

  7. C135910E01
    w/ Downhill assist control only
    Check the downhill assist control operation switch.

    1. w/o Multi-information display:
      Check that the VSC warning light is blinking as shown in the illustration.

    2. w/ Multi-information display:
      Check that the master caution indicator light blinks and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.

    3. Check the downhill assist control switch.

      1. Push the downhill assist control switch on.
      2. Push the downhill assist control switch off.

  8. Check the end of sensor.

    1. When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.

      NOTICE:
      If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.

  9. Read the DTCs of signal check function.

    1. Read the DTC(s) by following the instructions on the tester screen.

      NOTICE:
      1. If only the DTCs are displayed, repair the malfunction area and clear the DTCs.
      2. If the DTCs or Test Mode codes (DTC of signal check function) are displayed, repair the malfunction area, clear the DTCs and perform the Test Mode inspection.

      HINT:
      See the list of the DTCs (refer to "DTC OF TEST MODE FUNCTION (SIGNAL CHECK)" below).


CHECK SENSOR SIGNAL BY TEST MODE (When not Using Intelligent Tester)

  1. Procedures for test mode:

    1. Turn the ignition switch off.

    2. Check that the steering wheel is in the straight-ahead position.

    3. A/T:
      Check that the shift lever is in the P position and apply the parking brake.

    4. M/T:
      Check that the shift lever is in neutral and apply the parking brake.

    5. H100769E03
      Using SST, connect terminals 12 (TS) and 14 (CG) of the DLC3.
      SST
      09843-18040  

    6. Turn the ignition switch on (IG).

    7. C135910E01
      w/o Multi-information display:
      Check that the ABS warning light and VSC warning light blink as shown in the illustration.

    8. w/ Multi-information display:
      Check that the ABS warning light and master caution indicator light blink and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.

      HINT:
      If the ABS warning light and VSC warning warning light and multi-information display and master caution indicator light do not blink, check the TS and CG terminal circuit, and ABS and VSC warning light circuits.
      Section Title
      See procedure
      ABS Warning Light does not Come ON
      Click here
      VSC Warning Light does not Come ON
      Click here
      TS and CG Terminal Circuit
      Click here

    9. Start the engine.

  2. w/ 16-inch disc:
    Check the lost booster pressure judgment and perform the master cylinder pressure sensor zero point calibration.

    NOTICE:
    Preform the check in the lost booster pressure state (negative pressure in the booster is depressurized).


    1. Turn the ignition switch on (IG).

    2. Check that the BRAKE warning light comes on when depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more. (The lost booster pressure state is judged normal.)

    3. Start the engine depressing the brake pedal with a force of 59 N (6 kgf, 13.2 lbf) or more for 1 second or more.

    4. Check that the Brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged normal.)

    5. Leave the vehicle for 1 second or more. (Master cylinder pressure sensor zero point calibration.)

      NOTICE:
      1. If you slowly depress the brake pedal or depress it again, master cylinder pressure sensor zero point calibration is not performed normally.
      1. If the lost booster pressure judgment check is not completed normally, the master cylinder pressure sensor check is not judged.
      1. If a recheck is performed after the engine has started, end the Test Mode, enter Test Mode again, and release the vacuum in the booster by pumping the brake pedal prior to the recheck.

  3. Check the deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 1 second or more.

      HINT:
      The deceleration sensor check can be performed together with the following master cylinder pressure sensor check.

  4. Check the master cylinder pressure sensor.

    1. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
      Check that the ABS warning light remains illuminated for 3 seconds.

      HINT:
      1. Ensure that the ABS warning light comes on.
      2. While the ABS warning light remains illuminated, continue depressing the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
      3. The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.

  5. Check the speed sensor.

    1. C108848E01
      Check that the ABS warning light is blinking as shown in the illustration.

    2. Check the speed sensor signal.

      1. Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds.
      2. Check that the ABS warning light goes off.

        NOTICE:
        1. The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
        2. If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
        3. The ABS warning light comes on immediately when an abnormality is detected.
        4. When the speed sensor signal is normal, the ABS warning light goes off while driving at 45 km/h (28 mph) or more, and blinks in the test mode pattern while the vehicle is stationary.

        5. Do not drive the vehicle at a speed of 80 km/h (50 mph) or more after the ABS warning light turns off, because test mode DTCs are set again when the vehicle speed exceeds 80 km/h (50 mph).

          C115115E04

      3. Stop the vehicle.

  6. Check the yaw rate sensor.

    1. Move the shift lever to P and set the parking brake lever.

    2. C135910E01
      w/o Multi-information display:
      Check that the VSC warning light is blinking as shown in the illustration.

    3. w/ Multi-information display:
      Check that the master caution indicator light blinks and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.

    4. Keep the vehicle stationary on a level surface for 1 second or more.

    5. F002135E15
      Shift the shift lever to the D position (A/T) and drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more to turn the vehicle through 180°.

    6. A/T:
      Stop the vehicle, move the shift lever into the P position, and then apply the parking brake.

    7. M/T:
      Stop the vehicle, move the shift lever into neutral, and then apply the parking brake.

    8. Check that the skid control buzzer sounds for 3 seconds.

      HINT:
      1. If the skid control buzzer sounds, the signal check has been completed normally.
      2. If the skid control buzzer does not sound, check the skid control buzzer circuit (Click here).
      3. If the skid control buzzer still does not sound, there is a malfunction in the yaw rate sensor, so check for DTCs.
      4. Drive the vehicle in a 180° semi circle. At the end of the turn, the direction of the vehicle should be within 180 +-5° of its start position.
      5. Complete the vehicle turn within 20 seconds.
      6. Do not spin the wheels.

  7. C135910E01
    w/ Downhill assist control only
    Check the downhill assist control operation switch.

    1. w/o Multi-information display:
      Check that the VSC warning light is blinking as shown in the illustration.

    2. w/ Multi-information display:
      Check that the master caution indicator light blinks and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.

    3. Check the downhill assist control switch.

      1. Push the downhill assist control switch on.
      2. Push the downhill assist control switch off.

  8. Check the end of the sensor.

    1. When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.

      NOTICE:
      If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.

  9. Read the DTCs of the signal check function.

    1. H100769E17
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

    2. Turn the ignition switch on.

    3. w/o Multi-information display:
      Count the number of blinks of the ABS and VSC warning light.
      C131008E01

    4. w/ Multi-information display:
      Count the number of blinks of the ABS warning light, and read "[ABS]" and "[VSC]" indication on the multi-information display.

      HINT:
      1. The master caution indicator light also illuminates at the same time.
      2. DTCs of the ABS and VSC can be read by pressing the display switch of the combination meter. The multi-information display will display the DTCs with a "[ABS]" or "[VSC]" prefix.

      NOTICE:
      1. If only DTCs are displayed, repair the malfunctioning area and clear the DTCs.
      2. If the DTCs or test mode codes (DTC of signal check function) are displayed, repair the malfunctioning area, clear the DTCs and perform the test mode inspection.

      HINT:
      1. If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
      2. If DTCs or test mode codes are not displayed, the ABS warning light outputs the normal system code (the light comes on and goes off at 0.25 second intervals) or "FF" is displayed on the multi-information display.
      3. See the list of DTCs (refer to "DTC OF TEST MODE FUNCTION (SIGNAL CHECK)" below).
      4. If all sensors are normal, a normal system code is output (the light comes on for 0.25 seconds at intervals of 0.25 seconds).

    5. After the check, disconnect SST from terminals TC and CG of DLC3.

    6. Turn the ignition switch off.


DTC OF TEST MODE FUNCTION (SIGNAL CHECK)
DTC of ABS sensor check function: 
DTC No.
Diagnosis
Trouble Areas
C1271/71
Low output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
C1272/72
Low output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
C1273/73
Low output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
C1274/74
Low output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
C1275/75
Abnormal change in output signal of front speed sensor RH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1276/76
Abnormal change in output signal of front speed sensor LH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1277/77
Abnormal change in output signal of rear speed sensor RH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1278/78
Abnormal change in output signal of rear speed sensor LH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1279/79
Deceleration sensor output voltage malfunction
  1. Yaw rate sensor
  2. Sensor installation
C1281/81
Master cylinder pressure sensor output malfunction
  1. Master cylinder pressure sensor
  2. Brake pedal load sensing switch (w/ 16-inch disc)
DTC of VSC sensor check function: 
DTC No.
Diagnosis
Trouble Areas
C0371/71
Yaw rate sensor
Yaw rate sensor
C1389/74*
Downhill Assist Control operation switch
Downhill assist control switch

HINT:
  1. *: w/ Downhill assist control
  2. The DTCs in this table are only output in Test Mode.
  3. The detection of DTCs from C1271/71 to C1274/74 is completed before the vehicle speed reaches 5 km/h (3 mph).
  4. The detection of DTCs from C1275/75 to C1278/78 is completed before the vehicle speed reaches 45 km/h (28 mph).
  5. C1271/71 to C1274/74: The speed output from only one wheel is extremely low despite other wheel speed outputs reaching 5 km/h (3 mph).

  6. F100272E02
    C1275/75 to C1278/78: The abnormal speed sensor output frequency is as shown in the illustration.

← CALIBRATION (from Aug 2008)TEST MODE PROCEDURE (Jan 2007 – Jul 2007) →