2005-2008 RAV4 · Service Manual ENGINE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


EURO-OBD (EUROPE)
When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
FI02547E03
  1. The emission control system components

  2. The power train control components (which affect vehicle emissions)

  3. A127946
    B127990E01
    The computer
    In addition, if the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.

    HINT:
    When a problem is detected, "CHECK ENGINE SYSTEM" appears in the multi-information display (the combination's MIL does not illuminate).

    To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector3 (DLC3) of the vehicle.
    The scan tool displays DTCs, the freeze frame data and a variety of engine data.
    The DTCs and freeze frame data can be erased the scan tool (Click here).


M-OBD (EXCEPT EUROPEAN SPEC.)
When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in:
FI02547E03
  1. The emission control system/components

  2. The power train control components (which affect vehicle emissions)

  3. The computer
    In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.


NORMAL MODE AND CHECK MODE
The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (intelligent tester only).

2-TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected again after the ignition switch is turned off and then on (IG), the MIL illuminated.
A082779E98

DLC3 (Data Link Connector 3)
If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

HINT:
Connect the cable of an intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.

Symbol
Terminal No.
Name
Reference terminal
Result
Condition
SIL
7
Bus "+" line
5 - Signal ground
Pulse generation
During transmission
CG
4
Chassis ground
Body ground
1Ω or less
Always
SG
5
Signal ground
Body ground
1Ω or less
BAT
16
Battery positive
Body ground
9 to 14 V
CANH
6
CAN "High" Line
14 - CANL
54 to 69 Ω
Ignition switch off*
Battery positive
1 MΩ or higher
4 - CG
200 Ω or higher
CANL
14
CAN "Low" Line
Battery positive
1 MΩ or higher
4 - CG
200 Ω or higher

NOTICE:
*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, other switches and doors.


INSPECT BATTERY VOLTAGE
If the voltage is below 11 V, replace the battery before proceeding to the next step.

Battery Voltage:
11 to 14 V


CHECK MIL
  1. Check that the MIL illuminate when the ignition switch is turned on (IG).
    If the MIL does not illuminate, there is a problem in the MIL circuit (Click here).

  2. When the engine is started, the MIL should turn off.

← DIAGNOSIS SYSTEM (Nov 2005 – Dec 2006)DIAGNOSIS SYSTEM (from Aug 2007) →