P0110 Intake Air Temperature Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0112 Intake Air Temperature Circuit Low Input
- P0113 Intake Air Temperature Circuit High Input
DESCRIPTION


- The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT drops, the resistance of the thermistor increases. When the temperature rises, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).
- The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
- Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.
- HINT:
- When any of DTCs P0110, P0112 and P0113 are set, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
| DTC No. |
Proceed to |
DTC Detection Condition |
Trouble Area |
| P0110 |
Step 2 |
Open or short in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0112 |
Step 6 |
Short in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0113 |
Step 4 |
Open in Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic) |
|
- HINT:
- When any of these DTCs are set, check the IAT by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
| 1. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC output)
Proceed to
P0110
A
P0112
B
P0113
C
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTAKE AIR TEMPERATURE SENSOR (INTAKE AIR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
- Standard:
- Same as actual Intake Air Temperature (IAT).
- Result:
Temperature Displayed
Proceed to
-40°C (-40°F)
A
140°C (284°F) or higher
B
Same as actual IAT
C
- HINT:
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.
- If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.
|
|
||||
|
|
||||
| A | |
| 3. CHECK MASS AIR FLOW METER (CHECK FOR OPEN IN SENSOR) |
Confirm the good connection of the Mass Air Flow (MAF) meter.

Disconnect the MAF meter connector.
Connect the terminals THA and E2 of the MAF meter wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
- Standard:
- 140°C (284°F) or higher
Reconnect the MAF meter connector.
|
|
||||
| NG | |
| 4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the MAF meter connector.

Disconnect the ECM connector.
Measure the resistance between the terminals.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
THA (B96-71) - THA (B1-1)
Below 1 Ω
ETHA (B96-74) - E2 (B1-2)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
THA (B96-71) or THA (B1-1) - Body ground
10 kΩ or higher
ETHA (B96-74) or E2 (B1-2) - Body ground
10 kΩ or higher
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
| 5. CHECK MASS AIR FLOW METER (CHECK FOR SHORT IN SENSOR) |
Disconnect the MAF meter connector.

Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value displayed on the tester.
- Standard:
- -40°C (-40°F) or higher
Reconnect the MAF meter connector.
|
|
||||
| NG | |
| 6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER- ECM) |
Disconnect the MAF meter connector.

Disconnect the ECM connector.
Measure the resistance between the terminals.
- Standard resistance:
Tester Connection
Specified Condition
THA (B96-71) or THA (B1-1) - Body ground
10 kΩ or higher
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
