2005-2008 RAV4 · Service Manual ENGINE

P0115 Engine Coolant Temperature Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor, of which the resistance value varies according to the ECT.
The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:
When any of DTCs P0115, P0117 and P0118 are set, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.

DTC No.
Proceed to
DTC Detection Condition
Trouble Area
P0115
Step 2
Open or short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open or short in ECT sensor circuit
  1. ECT sensor
  1. ECM
P0117
Step 6
Short in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in ECT sensor circuit
  1. ECT sensor
  1. ECM
P0118
Step 4
Open in Engine Coolant Temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in ECT sensor circuit
  1. ECT sensor
  1. ECM

HINT:
When any of these DTCs are set, check the ECT by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit

WIRING DIAGRAM

A136302E07

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0115
    A
    P0117
    B
    P0118
    C



B
Go to step 6

C
Go to step 4
A


2. READ VALUE USING ENGINE COOLANT TEMPERATURE SENSOR (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    Between 80°C and 97°C (176°F and 207°F) with warm engine.


    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Between 80°C and 97°C (176°F and 207°F)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3. CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR OPEN IN SENSOR)

  1. A107691E55
    Confirm the good connection of the sensor.

  1. Disconnect the engine coolant temperature (ECT) sensor connector.

  1. Connect the terminals 1 and 2 of the ECT sensor connector on the wire harness side.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher

  1. Reconnect the ECT sensor connector.



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
NG


4. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A135019E14
    Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    THW (B96-79) - THW (B4-2)
    Below 1 Ω
    ETHW (B96-78) - E2 (B4-1)
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reconnect the ECT connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK ENGINE COOLANT TEMPERATURE SENSOR (CHECK FOR SHORT IN SENSOR)

  1. A172732E02
    Disconnect the ECT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the ECT sensor connector.



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
NG


6. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A135019E15
    Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    THW (B96-79) or THW (B4-2) - Body ground
    10 kΩ or higher

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0110 Intake Air Temperature Circuit Malfunction (+ P0112, P0113) (from Aug 2007)P0116 Engine Coolant Temperature Circuit Range / Performance Problem (from Aug 2007) →