2005-2008 RAV4 · Service Manual CRUISE CONTROL SYSTEM

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built Nov 2005 – Jul 2007

Versions by build date: Nov 2005 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008


CRUISE CONTROL SYSTEM (for 1AZ-FE, 2AZ-FE)
This system is controlled by the ECM, and is activated by the throttle position sensor and motor. The ECM controls the following functions: ON-OFF, SET / COAST, RESUME / ACCEL, CANCEL, vehicle speed operation, motor output control, and overdrive control.
  1. The ECM compares the driving vehicle speed from the combination meter with the stored vehicle speed set through the cruise control switch. The ECM controls the throttle valve motor of the throttle body to open the valve when the driving speed is less than the stored speed.
  2. The ECM receives signals such as ON-OFF, SET / COAST, RESUME / ACCEL, and CANCEL from the cruise control switch.
  3. The ECM illuminates the combination meter CRUISE main indicator light when it receives the cruise control switch ON signal.
  4. The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives the stop light switch signal.
  5. The ECM cancels the cruise control system when the shift lever is moved from D or 3 to a position other than D or 3, and the ECM receives the PNP switch signal (A/T).
  6. The ECM cancels the cruise control system when the clutch pedal is depressed and the ECM receives the clutch switch signal (M/T).

CRUISE CONTROL SYSTEM (for 2AD-FTV, 2AD-FHV)
The cruise control system controls the vehicle speed by using the ECM to change the fuel injection quantity. The ECM controls the following functions: ON-OFF, SET/COAST, RESUME/ACCEL, CANCEL, vehicle speed operation, motor output control, and overdrive control.
  1. The ECM compares the vehicle speed from the speed sensor with the stored vehicle speed set through the cruise control switch. When the actual vehicle speed exceeds the stored vehicle speed, the ECM decreases the fuel injection quantity. When the actual vehicle speed is less than the stored vehicle speed, the ECM increases the fuel injection quantity.
  2. The ECM receives signals such as ON-OFF, SET/COAST, RESUME/ACCEL, and CANCEL from the cruise control switch.
  3. The ECM illuminates the combination meter's CRUISE main indicator light when it receives the cruise control switch ON signal.
  4. The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives the stop light switch signal.
  5. The ECM cancels the cruise control system when the clutch pedal is depressed and the ECM receives the clutch switch signal.

LIMIT CONTROL
  1. Low speed limit
    The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit. Cruise control operation will be automatically canceled when the vehicle speed decreases below the low speed limit 40 km/h (25 mph) while the cruise control is in operation.

  2. High speed limit
    The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph). The cruise control system cannot be set when the driving vehicle speed is over the high speed limit. Also, +/RES cannot be used to increase speed beyond the high speed limit.


OPERATION OF CRUISE CONTROL (for 1AZ-FE, 2AZ-FE)
The cruise control switch operates 7 functions: SET, COAST, TAP-DOWN, RESUME, ACCELERATION (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN and COAST functions, and the RESUME, TAP-UP and ACCEL functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only when pressed in each arrow direction and turns off when released.
  1. SET CONTROL
    Vehicle speed is stored and constant speed control is maintained when pushing the switch to -/SET while driving with the cruise control switch ON (the CRUISE main indicator light is illuminated), and the vehicle speed is within the set speed range (between the low and high speed limits).

  2. COAST CONTROL
    The ECM changes the cruise control demanding throttle opening angle to 0° and decelerates the vehicle when -/SET on the cruise control switch is pressed and held while the cruise control system is operating. When the cruise control switch is released from -/SET, the vehicle speed is stored and constant speed control is maintained.

    HINT:
    1. The throttle valve is not fully closed due to idle speed control, etc.
    2. w/ VSC:
      The brake is also used to decelerate the vehicle.

  3. TAP-DOWN CONTROL
    When tapping down the cruise control switch to -/SET (for approximately 0.5 seconds) while the cruise control system is in operation, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control switch is released from -/SET and the difference between the driving and stored vehicle speed is less than 5 km/h (3 mph), the vehicle speed is stored and constant speed control is maintained.

  4. ACCEL CONTROL
    The throttle valve motor of the throttle position sensor and motor is instructed by the ECM to open the throttle valve when +/RES on the cruise control switch is pressed and held while the cruise control system is operating. When the cruise control switch is released from +/RES, the vehicle speed is stored and constant speed is maintained.

  5. TAP-UP CONTROL
    When tapping up the cruise control switch to +/RES (for approximately 0.5 seconds) while the cruise control system is in operation, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (approximately 3.1 mph), the stored vehicle speed will not be changed.

  6. RESUME CONTROL
    If the cruise control operation was canceled with the stop light switch or the CANCEL switch, and if driving speed is within the set speed range, setting the cruise control switch to +/RES restores the vehicle speed memorized at the time of cancellation, and constant speed is maintained.

  7. MANUAL CANCEL CONTROL
    Performing any of the following cancels the cruise control system (the stored vehicle speed in the ECM is maintained).

    1. Depressing the brake pedal
    2. Pulling the cruise control switch to CANCEL
    3. Moving the shift lever to any position except D or 3 (A/T)
    4. Depressing the clutch Pedal (M/T)


OPERATION OF CRUISE CONTROL (for 2AD-FTV, 2AD-FHV)
The cruise control switch operates 7 functions: SET, COAST, TAP-DOWN, RESUME, ACCELERATION (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN and COAST functions, and the RESUME, TAP-UP and ACCEL function are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only when pressed in each arrow direction and turns off when released.
  1. SET CONTROL
    Vehicle speed is stored and constant speed control is maintained when setting the switch to SET COAST while driving with the cruise control switch ON (the CRUISE main indicator light is illuminated), and the vehicle speed is within the set speed range (between the low and high speed limits).

  2. COAST CONTROL
    When the SET/COAST on the cruise control switch is pressed and held while the cruise control system is operating, ECM changes the required fuel injection quantity to 0 and decelerates the vehicle. When the cruise control switch is released from SET/COAST, the vehicle speed is stored and constant speed control is maintained.

    HINT:
    w/ VSC:
    The brake is also used to decelerate the vehicle.

  3. TAP-DOWN CONTROL
    When tapping down the cruise control switch to SET/COAST (for approximately 0.6 seconds) while the cruise control system is operating, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control switch is released from SET/COAST and the difference between the driving and stored vehicle speed is less than 5 km/h (3 mph), the vehicle speed is stored and constant speed is maintained.

  4. ACCEL CONTROL
    While the cruise control system is activated, if the main switch is set to RESUME/ACCEL, the EDU increases the fuel injection quantity. When the cruise control switch is released from RESUME/ACCEL, the vehicle speed is stored and constant speed is maintained.

  5. TAP-UP CONTROL
    When tapping up the cruise control switch to RESUME/ACCEL (for approximately 0.6 seconds) while the cruise control system is operating, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (3 mph), the stored vehicle speed will not be change.

  6. RESUME CONTROL
    If the cruise control operation was canceled with the stop light switch or the CANCEL switch and if driving speed is within the set speed range, setting the cruise control switch to RESUME/ACCEL restores the vehicle speed memorized at the time of cancellation and constant speed is maintained.

  7. MANUAL CANCEL CONTROL
    Performing any of the following cancels the cruise control system.

    1. Depressing the brake pedal
    2. Pulling the cruise control switch to CANCEL
    3. Pushing the cruise control switch OFF
    4. Depressing the clutch pedal


AUTO CANCEL (FAIL-SAFE)
This system has an automatic cancellation function (fail-safe) (Click here).
← SYSTEM DIAGRAM (from Aug 2007)SYSTEM DESCRIPTION (Aug 2007 – Jul 2008) →