SYSTEM DESCRIPTION
Troubleshooting · Vehicles built Aug 2007 – Jul 2008
Versions by build date: Nov 2005 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008
| CRUISE CONTROL SYSTEM (for 1AZ-FE, 2AZ-FE, 2GR-FE) |
- The ECM compares the driving vehicle speed from the combination meter with the stored vehicle speed set through the cruise control switch. The ECM controls the throttle valve motor of the throttle body to open the valve when the driving speed is less than the stored speed.
- The ECM receives signals such as ON-OFF, - (COAST)/SET, + (ACCEL)/RES, and CANCEL from the cruise control switch.
- The ECM illuminates the combination meter's CRUISE main indicator light when it receives the cruise control switch ON signal.
- The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives the stop light switch signal.
- The ECM cancels the cruise control system when the shift lever is moved from D, 4 or 3 to a position other than D, 4 or 3 and the ECM receives the PNP switch signal (for A/T).
- The ECM cancels the cruise control system when the clutch pedal is depressed and the ECM receives the clutch switch signal (for M/T).
| CRUISE CONTROL SYSTEM (for 2AD-FTV, 2AD-FHV) |
- The ECM compares the vehicle speed from the speed sensor with the stored vehicle speed set through the cruise control switch. When the actual vehicle speed exceeds the stored vehicle speed, the ECM decreases the fuel injection quantity. When the actual vehicle speed is less than the stored vehicle speed, the ECM increases the fuel injection quantity.
- The ECM receives signals such as ON-OFF, - (COAST)/SET, + (ACCEL)/RES, and CANCEL from the cruise control switch.
- The ECM illuminates the combination meter's CRUISE main indicator light when it receives the cruise control switch ON signal.
- The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives the stop light switch signal.
- The ECM cancels the cruise control system when the clutch pedal is depressed and the ECM receives the clutch switch signal.
| LIMIT CONTROL |
Low speed limit
The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit. Cruise control operation will be automatically canceled when the vehicle speed decreases below the low speed limit 40 km/h (25 mph) while the cruise control is in operation.High speed limit
The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph). The cruise control system cannot be set when the driving vehicle speed is over the high speed limit. Also, +/RES cannot be used to increase speed beyond the high speed limit.
| OPERATION OF CRUISE CONTROL (for 1AZ-FE, 2AZ-FE, 2GR-FE) |
SET CONTROL
Vehicle speed is stored and constant speed control is maintained when pushing the switch to -/SET while driving with the cruise control switch ON (the CRUISE main indicator light is illuminated), and the vehicle speed is within the set speed range (between the low and high speed limits).COAST CONTROL
The ECM changes the cruise control demanding throttle opening angle to 0° and decelerates the vehicle when -/SET on the cruise control switch is pressed and held while the cruise control system is operating. When the cruise control switch is released from -/SET, the vehicle speed is stored and constant speed control is maintained.- HINT:
- The throttle valve is not fully closed due to idle speed control, etc.
- w/ VSC:
The brake is also used to decelerate the vehicle.
- The throttle valve is not fully closed due to idle speed control, etc.
TAP-DOWN CONTROL
When tapping down the cruise control switch to -/SET (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control switch is released from -/SET and the difference between the driving and the stored vehicle speed is less than 5 km/h (3 mph), the vehicle speed is stored and constant speed control is maintained.ACCEL CONTROL
The throttle valve motor of the throttle position sensor and motor is instructed by the ECM to open the throttle valve when +/RES on the cruise control switch is pressed and held while the cruise control system is operating. When the cruise control switch is released from +/RES, the vehicle speed is stored and constant speed is maintained.TAP-UP CONTROL
When tapping up the cruise control switch to +/RES (for approximately 0.6 seconds) while the cruise control system is in operation, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (approximately 3 mph), the stored vehicle speed will not be changed.RESUME CONTROL
If the cruise control operation was canceled with the stop light switch or the CANCEL switch, and if driving speed is within the set speed range, setting the cruise control switch to +/RES restores the vehicle speed memorized at the time of cancellation, and constant speed is maintained.MANUAL CANCEL CONTROL
Performing any of the following cancels the cruise control system (the stored vehicle speed in the ECM is maintained).- Depressing the brake pedal
- Pulling the cruise control switch to CANCEL
- Moving the shift lever to any position except D, 4 or 3 (for A/T)
- Depressing the clutch pedal (for M/T)
- Pushing the cruise control main switch OFF (the stored vehicle speed in the ECM is not maintained)
- Depressing the brake pedal
| OPERATION OF CRUISE CONTROL (for 2AD-FTV, 2AD-FHV) |
SET CONTROL
Vehicle speed is stored and constant speed control is maintained when setting the switch to - (COAST)/SET while driving with the cruise control switch ON (the CRUISE main indicator light is illuminated), and the vehicle speed is within the set speed range (between the low and high speed limits).COAST CONTROL
When the - (COAST)/SET on the cruise control switch is pressed and held while the cruise control system is operating, the ECM changes the required fuel injection quantity to 0 and decelerates the vehicle. When the cruise control switch is released from - (COAST)/SET, the vehicle speed is stored and constant speed control is maintained.- HINT:
- w/ VSC:
- The brake is also used to decelerate the vehicle.
TAP-DOWN CONTROL
When tapping down the cruise control switch to - (COAST)/SET (for approximately 0.6 seconds) while the cruise control system is operating, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control switch is released from - (COAST)/SET and the difference between the driving and the stored vehicle speed is less than 5 km/h (3 mph), the vehicle speed is stored and constant speed is maintained.ACCEL CONTROL
While the cruise control system is activated, if the main switch is set to + (ACCEL)/RES, the EDU increases the fuel injection quantity. When the cruise control switch is released from + (ACCEL)/RES, the vehicle speed is stored and constant speed is maintained.TAP-UP CONTROL
When tapping up the cruise control switch to + (ACCEL)/RES (for approximately 0.6 seconds) while the cruise control system is operating, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (3 mph), the stored vehicle speed will not be changed.RESUME CONTROL
If the cruise control operation was canceled with the stop light switch or the CANCEL switch and if driving speed is within the set speed range, setting the cruise control switch to + (ACCEL)/RES restores the vehicle speed memorized at the time of cancellation and constant speed is maintained.MANUAL CANCEL CONTROL
Performing any of the following cancels the cruise control system.- Depressing the brake pedal
- Pulling the cruise control switch to CANCEL
- Depressing the clutch pedal
- Pushing the cruise control main switch OFF (the stored vehicle speed in the ECM is not maintained)
- Depressing the brake pedal
| AUTO CANCEL (FAIL-SAFE) |