2005-2008 RAV4 · Service Manual ENGINE

P0230 Fuel Pump Primary Circuit

Diagnostic trouble codes · Vehicles built from Aug 2007

DESCRIPTION

When the engine is cranked, a signal is sent from the ignition control ECU's STSW terminal to the ECM's STSW terminal. Then voltage travels from the ECM's STAR terminal through the park/neutral position switch to the STARTER relay coil. The STAR terminal also sends a signal to the STA terminal. When the STA signal and NE signal are input to the ECM, the ECM interior's Tr1 turns on, which causes power to be supplied to the C/OPN relay coil (C/OPN on). As a result, the F/PMP relay actuates, which causes the fuel pump to operate. If the engine is operating and NE signals are being output, the ECM interior's Tr1 is on (C/OPN on), and the fuel pump will continue operating. The fuel pump's has a high and low speed setting. When the engine is starting or operating with a heavy load, the ECM interior's Tr2 turns on to actuate the F/PMP relay so that the fuel pump operates at the high speed setting. When the engine is idling or operating with a light load, the Tr2 turns off, and current flows through the fuel pump resister to the fuel pump so that the fuel pump operates at the low speed setting.
A172781E01
DTC No.
DTC Detection Condition
Trouble Area
P0230
Open or short in F/PMP relay circuit (1 trip detection logic)
  1. Open or short in F/PMP relay circuit
  2. F/PMP relay
  3. ECM

WIRING DIAGRAM

A153034E03
This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the problem symptoms table (Click here).

INSPECTION PROCEDURE


1. CHECK TERMINAL VOLTAGE (F/PMP RELAY POWER SOURCE)
A172733E01
  1. Remove the F/PMP relay from the engine room No. 1 relay block.

  1. Measure the voltage of the engine room No. 1 relay block terminal.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F/PMP relay holder terminal (2) - Body ground
    STA signal ON
    9 to 14 V
    F/PMP relay holder terminal (2) - Body ground
    STA signal OFF
    0 to 3 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (F/PMP RELAY - EFI MAIN RELAY)
OK


2. INSPECT RELAY (Marking: F/PMP)

  1. A087121E10
    Remove the F/PMP relay from the engine room No. 1 relay block.

  1. Measure the resistance of the F/PMP relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 4
    10 kΩ or higher
    (when battery voltage applied to terminals 1 and 2)
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)



NG
REPLACE RELAY
OK


3. CHECK HARNESS AND CONNECTOR (F/PMP RELAY - ECM)

  1. A137840E02
    Remove the F/PMP relay from the engine room No. 1 relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    F/PMP relay holder terminal (1) - B96-59 (FPR)
    Below 1 Ω
    F/PMP relay holder terminal (1) or B96-59 (FPR) - Body Ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0171 System Too Lean (Bank 1) (+ P0172, P0174, P0175) (from Aug 2007)P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (from Aug 2007) →