P0171 System Too Lean (Bank 1)
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0172 System Too Rich (Bank 1)
- P0174 System Too Lean (Bank 2)
- P0175 System Too Rich (Bank 2)
DESCRIPTION
The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
If both the short-term and long-term fuel trims are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and sets a DTC.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0171 P0174 |
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 P0175 |
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic) |
|
- HINT:
- When DTC P0171 or P0174 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air-fuel ratio is on the rich side.
- If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
- When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.
- When DTC P0171 or P0174 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air-fuel ratio is on the rich side.
MONITOR DESCRIPTION
Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and sets a DTC.- When the average fuel trim learning value is more than +35% or less than -35%, the ECM interprets this as a fuel system malfunction.


WIRING DIAGRAM
Refer to DTC P2195 (Click here).INSPECTION PROCEDURE
- HINT:
- For use of the intelligent tester only:
- Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
- The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
- Connect the intelligent tester to the DLC3.
- Start the engine and turn the tester on.
- Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
- Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
- Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
- Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
- HINT:
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Standard voltage:
Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1 (A/F)
+25%
Rich
Less than 3.0
AFS B1S1 or AFS B2S1 (A/F)
-12.5%
Lean
More than 3.35
O2S B1S2 or O2S B2S2 (HO2)
+25%
Rich
More than 0.55
O2S B1S2 or O2S B2S2 (HO2)
-12.5%
Lean
Less than 0.4
- NOTICE:
- The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum delay of approximately 20 seconds.
Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1




-
2




- Air fuel ratio sensor
- Air fuel ratio sensor heater
- Air fuel ratio sensor circuit
3




- Heated oxygen sensor
- Heated oxygen sensor heater
- Heated oxygen sensor circuit
4




- Fuel pressure
- Gas leakage from exhaust system
(Air fuel ratio extremely lean or rich)
- Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
- The following A/F Control procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors. To display the graph, select the following menu items on the tester: View / Line graph.
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
- A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
- A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0171, P0172, P0174 or P0175
A
P0171, P0172, P0174 or P0175 and other DTCs
B
- HINT:
- If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. CHECK PCV HOSE CONNECTIONS |
- OK:
- PCV hose is connected correctly and is not damaged.
|
|
||||
| OK | |
| 3. CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
- OK:
- No leakage from the air induction system.
|
|
||||
| OK | |
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
- HINT:
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Standard voltage:
Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1 (A/F)
+25%
Rich
Less than 3.0
AFS B1S1 or AFS B2S1 (A/F)
-12.5%
Lean
More than 3.35
O2S B1S2 or O2S B2S2 (HO2)
+25%
Rich
More than 0.55
O2S B1S2 or O2S B2S2 (HO2)
-12.5%
Lean
Less than 0.4
- Result:
Status AFS B1S1 or AFS B2S1
Status O2S B1S2 or O2S B2S2
A/F Condition and A/F Sensor Condition
Misfire
Suspected Trouble Area
Proceed to
Lean/Rich
Lean/Rich
Normal
-
-
C
Lean/Lean
Lean/Lean
Actual air-fuel ratio lean
May occur
- PCV valve and hose
- PCV hose connections
- Injector blockage
- Gas leakage from exhaust system
- Air induction system
- Fuel pressure
- Mass Air Flow (MAF) meter
- Engine Coolant Temperature (ECT) sensor
A
Rich/Rich
Rich/Rich
Actual air-fuel ratio rich
-
- Injector leakage or blockage
- Gas leakage from exhaust system
- Ignition system
- Fuel pressure
- MAF meter
- ECT sensor
A
Lean/Lean
Lean/Rich
A/F sensor malfunction
-
A/F sensor
B
Rich/Rich
Lean/Rich
A/F sensor malfunction
-
A/F sensor
B
- PCV valve and hose
|
|
||||
|
|
||||
| A | |
| 5. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
- Standard:
- With cold engine:
- Same as ambient air temperature.
- With warm engine:
- Between 75°C and 95°C (167°F and 203°F)
|
|
||||
| OK | |
| 6. READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2500 rpm.
- Standard:
- MAF when engine is stopped:
- Below 0.7 g/s
- MAF while engine is idling:
- Between 2.0 g/s and 5.0 g/s (shift position: N, A/C: OFF).
- MAF at an engine speed of 2500 rpm:
- Between 8.0 g/s and 19.0 g/s (shift position: N, A/C: OFF).
|
|
||||
| OK | |
| 7. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 8. CHECK FOR EXHAUST GAS LEAKS |
- OK:
- No gas leakage.
|
|
||||
| OK | |
| 9. CHECK FOR SPARKS AND IGNITION |
Check for sparks and ignition (Click here).
- HINT:
- If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the intelligent tester. Select the following menu items: Powertrain / Engine and ECT / Data List / Cylinder #1 (to #6) Misfire rate.
|
|
||||
| OK | |
| 10. INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Inspect the fuel injector assembly (Click here).
- HINT:
- If the injectors malfunction, engine misfire may occur. The misfire count can be read using the intelligent tester. Select the following menu items: Powertrain / Engine and ECT / Data List / Cylinder #1 (to #6) Misfire rate.
|
|
||||
| OK | |
| 11. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Disconnect the A/F sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- Bank 1:
Tester Connection
Condition
Specified Condition
HA1A (1) - +B (2)
20°C (68°F)
1.8 to 3.4 Ω
HA1A (1) - A1A- (4)
Always
10 kΩ or higher
- Bank 2:
Tester Connection
Condition
Specified Condition
HA2A (1) - +B (2)
20°C (68°F)
1.8 to 3.4 Ω
HA2A (1) - A2A- (4)
Always
10 kΩ or higher
Reconnect the A/F sensor connector.
|
|
||||
| OK | |
| 12. INSPECT INTEGRATION RELAY (A/F RELAY) |
Remove the integration relay from the engine room No. 1 relay block.

Measure the A/F relay resistance.
- Standard resistance:
Tester Connection
Specified Condition
1C-1 - 1B-8
10 kΩ or higher
1C-1 - 1B-8
Below 1 Ω
(when battery voltage is applied to terminals 1B-6 and 1B-7)
Reinstall the integration relay.
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the A/F sensor connector.

Measure the resistance.
- Standard resistance (Check for open):
- Bank 1:
Tester Connection
Specified Condition
HA1A (B7-1) - HA1A (B96-86)
Below 1 Ω
A1A+ (B7-3) - A1A+ (B96-93)
Below 1 Ω
A1A- (B7-4) - A1A- (B96-116)
Below 1 Ω
- Bank 2:
Tester Connection
Specified Condition
HA2A (B67-1) - HA2A (B96-109)
Below 1 Ω
A2A+ (B67-3) - A2A+ (B96-120)
Below 1 Ω
A2A- (B67-4) - A2A- (B96-119)
Below 1 Ω
- Standard resistance (Check for short):
- Bank 1:
Tester Connection
Specified Condition
HA1A (B7-1) or HA1A (B96-86) - Body ground
10 kΩ or higher
A1A+ (B7-3) or A1A+ (B96-93) - Body ground
10 kΩ or higher
A1A- (B7-4) or A1A- (B96-116) - Body ground
10 kΩ or higher
- Bank 1:
Tester Connection
Specified Condition
HA2A (B67-1) or HA2A (B96-109) - Body ground
10 kΩ or higher
A2A+ (B67-3) or A2A+ (B96-120) - Body ground
10 kΩ or higher
A2A- (B67-4) or A2A- (B96-119) - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the A/F sensor connector.
|
|
||||
| OK | |
| 14. REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15. PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3 (Procedure A).
Turn the ignition switch to the ON position and turn the tester on (Procedure B).
Clear the DTCs (Click here) (Procedure C).
Select the check mode using the tester (Click here) (Procedure D).
Start the engine and warm it up with all the accessories switched off (Procedure E).
Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes (Procedure F).


- HINT:
- If the system is still malfunctioning, the MIL will be illuminated during procedure "F".
- NOTICE:
- If the conditions in this test are not strictly followed, no malfunction will be detected.
| NEXT | |
| 16. CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P0174 OR P0175) |
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
No output
A
P0171, P0172, P0174 or P0175
B
|
|
||||
| A | ||
| ||
| 17. INSPECT FUSE (A/F FUSE) |
Remove the A/F fuse from the integration relay.

Measure the fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the fuse.
|
|
||||
| OK | ||
| ||
