P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built from Aug 2007
DESCRIPTION
While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0617 |
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic):
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the problem symptoms table (Click here).
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
- The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
| 1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
- Standard:
Ignition Switch Condition
Tester Display (Starter Signal)
On (IG)
OFF
Engine Starts
ON
- Result:
Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 2. INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
Disconnect the PNP switch connector.

Measure the resistance when the transmission gear selector lever is moved to each position.
- Standard resistance:
Gear Selector
Lever Position
Tester Connection
Specified Condition
P
2 - 6, 4 - 5
Below 1 Ω
R
1 - 2
N
2 - 9, 4 - 5
D
2 - 7
Reconnect the PNP switch connector.
|
|
||||
| NG | |
| 3. REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
| NEXT | |
| 4. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
- Standard:
Ignition Switch Condition
Tester Display (Starter Signal)
On
OFF
Engine Starts
ON
|
|
||||
| NG | |
| 5. INSPECT IGNITION SWITCH ASSEMBLY |
Disconnect the ignition switch connector.

Measure the resistance.
- Standard resistance:
Ignition Switch Position
Tester Connection
Specified Condition
LOCK
All Terminals
10 kΩ or higher
ACC
2 - 3
Below 1 Ω
ON
2 - 3, 2 - 4, 6 - 7
START
1 - 2, 2 - 4, 6 - 7, 7 - 8
Reconnect the ignition switch connector.
|
|
||||
| NG | |
| 6. REPLACE IGNITION SWITCH ASSEMBLY |
| NEXT | |
| 7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
- Standard:
Ignition Switch Condition
Tester Display (Starter Signal)
On
OFF
Engine Starts
ON
|
|
||||
| NG | |
| 8. REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 9. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0617
A
No DTC
B
|
|
||||
| A | ||
| ||
