P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built from Aug 2007
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0617 |
When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic): (a) Vehicle speed is more than 20 km/h (12.4 mph) (b) Engine speed is more than 1,000 rpm (c) STA signal is ON |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- The following troubleshooting process is based on the premise that the engine is cranked normally. If the engine will not crank, proceed to the problem symptoms table (Click here).
| 1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM |
- Result:
Result
Proceed to
w/o Entry and Start System
A
w/ Entry and Start System
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the on (IG) and Start positions.
- OK:
Ignition Switch Condition
Tester Display (Starter Signal)
ON
OFF
START
ON
|
|
||||
| NG | |
| 3. INSPECT IGNITION SWITCH ASSEMBLY |
Disconnect the ignition switch connector.
Measure the resistance of the ignition switch.

- Standard resistance:
Condition
Tester Condition
Specified Condition
OFF
Between all terminals
1 MΩ or more
ACC
2 - 3
1 Ω or less
ON
2 - 4, 6 - 7
1 Ω or less
START
1 - 2, 2 - 4, 6 - 7, 7 - 8
1 Ω or less
Reconnect the ignition switch connector.
|
|
||||
| NG | |
| 4. REPLACE IGNITION SWITCH |
| NEXT | |
| 5. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the on (IG) and Start positions.
- OK:
Ignition Switch Condition
Tester Display (Starter Signal)
ON
OFF
START
ON
|
|
||||
| NG | |
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 7. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Drive the vehicle at more than 12.4 mph (20 km/h) for over 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / Data List / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0617
A
No DTC
B
|
|
||||
| A | ||
| ||
| 8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the on (IG) and Start positions.
- OK:
Ignition Switch Condition
Tester Display (Starter Signal)
On (IG)
OFF
Engine starts
ON
|
|
||||
| NG | |
| 9. INSPECT CLUTCH START SWITCH |
Disconnect the clutch start switch connector.

Measure the resistance when the clutch start switch is ON and OFF.
- Standard resistance:
Ignition Switch Position
Tester Connection
Specified Condition
On (pushed)
1 - 2
Below 1 Ω
Off (not pushed)
1 - 2
10 kΩ or higher
Reconnect the clutch start switch connector.
|
|
||||
| OK | ||
| ||
