P0335 Crankshaft Position Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0339 Crankshaft Position Sensor "A" Circuit Intermittent
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet.The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0335 |
When either condition below is met:
|
|
| P0339 |
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic): (a) Engine speed 1,000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have lapsed since starter signal switched from ON to OFF |
|
-
Reference: Inspection using an oscilloscope.

- HINT:
- The correct waveform is as shown.
- The correct waveform is as shown.
- G2 stands for the CMP sensor signal, and NE+ stands for the CKP sensor signal.
- Grounding failure of the shielded wire may cause noise in waveforms.
- G2 stands for the CMP sensor signal, and NE+ stands for the CKP sensor signal.
Item
Content
Terminals
CH1: G2+ - G2-
CH2: NE+ - NE-
Equipment Settings
5 V/DIV.
20 msec./DIV.
Conditions
Cranking or idling
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
- Check the engine speed. The engine speed can be checked by using the intelligent tester. To check, follow the operation below:
- Connect the intelligent tester to the DLC3.
- Start the engine.
- Turn the tester ON.
- Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
- The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
| 1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
- OK:
- Correct values are displayed.
- HINT:
- To check the engine speed change, display the graph on the tester.
- If the engine does not start, check the engine speed while cranking.
- If the engine speed indicated on the tester remains zero(0), there may be an open or short in the crankshaft position sensor circuit.
- To check the engine speed change, display the graph on the tester.
|
|
||||
| NG | |
| 2. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE) |
![]() ![]() |
Disconnect the B22 Crankshaft Position (CKP) sensor connector.
Measure the resistance between terminals 1 and 2.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
985 to 1,600 Ω
1 - 2
Hot
1,265 to 1,890 Ω
- HINT:
- Terms cold and hot refer to the temperature of the sensor. Cold means approximately -10 to 50°C (14 to 122°F). Hot means approximately 50 to 100°C (122 to 212°F).
Reconnect the CKP sensor connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
![]() ![]() |
Disconnect the B22 CKP sensor connector.
Disconnect the B32 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
NE+ (B22-1) - NE+ (B32-122)
Below 1 Ω
NE- (B22-2) - NE- (B32-121)
- Standard resistance (Check for short):
Tester Connection
Specified Condition
NE+ (B22-1) or NE+ (B32-122) - Body ground
10 kΩ or higher
NE- (B22-2) or NE- (B32-121) - Body ground
Reconnect the ECM connector.
Reconnect the CKP sensor connector.
|
|
||||
| OK | |
| 4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
![]() ![]() |
Check the CKP sensor installation.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 5. CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE) |
Check the teeth of the sensor plate.
- OK:
- Sensor plate does not have any cracks or deformation.
|
|
||||
| OK | |
| 6. REPLACE CRANKSHAFT POSITION SENSOR |
| NEXT | |
| 7. CHECK WHETHER DTC OUTPUT RECURS |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC output)
Proceed to
No output
A
P0335 or P0339
B
- HINT:
- If the engine does not start, replace the ECM.
|
|
||||
| A | ||
| ||



