ECM Power Source Circuit
Circuit diagnosis · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
When the ignition switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. INSPECT INTEGRATION RELAY (INTEGRATION RELAY - BODY GROUND) |
Remove the integration relay from the engine room No. 1 relay block.

Measure the voltage of the terminal of the integration relay and body ground.
- Standard voltage:
Tester Connection
Specified Condition
1C-1 - Body ground
9 to 14 V
Reinstall the integration relay.
|
|
||||
| OK | |
| 2. INSPECT FUSE (EFI MAIN FUSE) |
Remove the EFI MAIN fuse from the integration relay.

Measure the EFI MAIN fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI MAIN fuse.
|
|
||||
| OK | |
| 3. INSPECT INTEGRATION RELAY (EFI MAIN RELAY) |
Remove the integration relay from the engine room No. 1 relay block.

Measure the EFI MAIN relay resistance.
- Standard resistance:
Tester Connection
Specified Condition
1C-1 - 1A-4
10 kΩ or higher
1C-1 - 1A-4
Below 1 Ω
(Apply battery voltage to terminals 1A-2 and 1A-3)
Reinstall the integration relay.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (+B AND MREL CIRCUIT) |
Check the wire harness between the ECM and integration relay.

Disconnect the ECM connector.
Remove the integration relay from the engine room No. 1 relay block.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A12-45 (MREL) - 1A-2
Below 1 Ω
A12-1 (+B) - 1A-4
Below 1 Ω
A12-45 (MREL) or 1A-2 - Body ground
10 kΩ or higher
A12-1 (+B) or 1A-4 - Body ground
10 kΩ or higher
Check the wire harness between the integration relay and body ground.
Measure the resistance of the wire harness side connector and body ground.
- Standard resistance:
Tester Connection
Specified Condition
1A-3 - Body ground
Below 1 Ω
Reconnect the ECM connector.
Reinstall the integration relay.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
Disconnect the ECM connector.

Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
B32-109 (E1) - Body ground
Below 1 Ω
Reconnect the ECM connector.
|
|
||||
| OK | |
| 6. INSPECT ECM (IGSW VOLTAGE) |
Disconnect the ECM connectors.

Turn the ignition switch on (IG).
Measure the voltage of the terminals of the ECM connectors.
- Standard voltage:
Tester Connection
Specified Condition
A12-25 (IGSW) - B32-109 (E1)
9 to 14 V
Reconnect the ECM connectors.
|
|
||||
| NG | |
| 7. INSPECT FUSE (IGN, G2) |
Remove the IGN fuse from the main body ECU (instrument panel junction block).

Remove the IG2 fuse from the engine room No. 1 relay block.

Measure the IGN and IG2 fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the IGN fuse.
Reinstall the IG2 fuse.
|
|
||||
| OK | |
| 8. INSPECT IGNITION RELAY NO. 2 |
![]() ![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Check the resistance.
- Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
3 - 5
Below 1 Ω
(When battery voltage applied to terminals 1 and 2)
Reinstall the relay.
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM NO. 1 RELAY BLOCK) |
Disconnect the ECM connector.

Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A12-25 (IGSW) - Relay block IG2 relay terminal 5
Below 1 Ω
A12-25 (IGSW) or Relay block IG2 relay terminal 5 - Body ground
10 KΩ or higher
Reconnect the ECM connector.
Reinstall the IG2 relay.
- Result:
Result
Proceed to
Out of normal range
A
Within normal range (w/ Entry and Start System)
B
Within normal range (w/o Entry and Start System)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE ROOM NO. 1 RELAY BLOCK) |
Remove the instrument panel junction block (main body ECU).

Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E19-5 (IG2D) - Relay block IG2 relay terminal 1
Below 1 Ω
Relay block IG2 relay terminal 2 - Body ground
Below 1 Ω
E19-5 (IG2D) - Body ground
10 kΩ or higher
Reconnect the main body ECU.
Reinstall the IG2 relay.
|
|
||||
| OK | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM NO. 1 RELAY BLOCK) |
Disconnect the ignition switch connector.

Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E5-6 (IG2) - Relay block IG2 relay terminal 1
Below 1 Ω
Relay block IG2 relay terminal 2 - Body ground
Below 1 Ω
E5-6 (IG2) - Body ground
10 kΩ or higher
Reconnect the ignition switch connector.
Reinstall the IG2 relay.
|
|
||||
| OK | |
| 12. INSPECT IGNITION SWITCH ASSEMBLY |
Disconnect the ignition switch connector.

Measure the resistance of the terminals shown below.
- Standard resistance:
Condition
Tester Condition
Specified Condition
Off
Between all terminals
1 MΩ or more
On (ACC)
2 - 3
1 Ω or less
On (IG)
2 - 4, 6 - 7
1 Ω or less
Start
1 - 2, 2 - 4, 6 - 7, 7 - 8
1 Ω or less
Reconnect the ignition switch connector.
|
|
||||
| OK | ||
| ||

