2005-2008 RAV4 · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

When the ignition switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

C128789E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. INSPECT INTEGRATION RELAY (INTEGRATION RELAY - BODY GROUND)

  1. A131567E01
    Remove the integration relay from the engine room No. 1 relay block.

  1. Measure the voltage of the terminal of the integration relay and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    1C-1 - Body ground
    9 to 14 V

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2. INSPECT INTEGRATION RELAY (EFI MAIN RELAY)
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Inspect the EFI MAIN fuse.

    1. A107921E20
      Remove the EFI MAIN fuse from the integration relay.

    2. Measure the EFI MAIN fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI MAIN fuse.

  1. Inspect the EFI MAIN relay.

    1. Measure the EFI MAIN relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1C-1 - 1A-4
      10 kΩ or higher
      1C-1 - 1A-4
      Below 1 Ω
      (Apply battery voltage to terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


3. CHECK WIRE HARNESS (+B AND MREL CIRCUIT)

  1. A131574E01
    Check the wire harness between the ECM and integration relay.
    1. Disconnect the A12 ECM connector.

    2. Remove the integration relay from the engine room No. 1 relay block.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      A12-45 (MREL) - 1A-2
      Below 1 Ω
      A12-1 (+B) - 1A-4
      Below 1 Ω
      A12-45 (MREL) or 1A-2 - Body ground
      10 kΩ or higher
      A12-1 (+B) or 1A-4 - Body ground
      10 kΩ or higher

  1. Check the wire harness between the integration relay and body ground.

    1. Measure the resistance of the wire harness side connector and body ground.

      Standard resistance:
      Tester Connection
      Specified Condition
      1A-3 - Body ground
      Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. CHECK WIRE HARNESS (ECM - BODY GROUND)

  1. A107892E45
    Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    B32-109 (E1) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. INSPECT ECM (IGSW VOLTAGE)

  1. A130158E03
    Disconnect the A12 and B32 ECM connectors.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the terminals of the A12 and B32 ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    A12-25 (IGSW) - B32-109 (E1)
    9 to 14 V

  1. Reconnect the ECM connectors.



OK
REPLACE ECM
NG


6. INSPECT FUSE (IGN, G2)

  1. A127848E04
    Remove the IGN fuse from the main body ECU (instrument panel junction block).

  1. A130321E02
    Remove the IG2 fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.

  1. Reinstall the IG2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


7. INSPECT IGNITION RELAY NO. 2
B060778E76
  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Check the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage applied to terminals 1 and 2)

  1. Reinstall the relay.



NG
REPLACE IGNITION RELAY NO. 2
OK


8. CHECK WIRE HARNESS (ECM - ENGINE ROOM NO. 1 RELAY BLOCK)
A131568E02
  1. Disconnect the A12 ECM connector.

  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A12-25 (IGSW) - Relay block IG2 relay terminal 5
    Below 1 Ω
    A12-25 (IGSW) or Relay block IG2 relay terminal 5 - Body ground
    10 KΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the IG2 relay.

    Result:
    Result
    Proceed to
    Out of normal range
    A
    Within normal range (w/ Entry and Start System)
    B
    Within normal range (w/o Entry and Start System)
    C



B
Go to step 9

C
CHECK WIRE HARNESS (IGNITION SWITCH - ENGINE ROOM NO. 1 RELAY BLOCK)
A

REPAIR OR REPLACE HARNESS AND CONNECTOR

9. CHECK WIRE HARNESS (MAIN BODY ECU - ENGINE ROOM NO. 1 RELAY BLOCK)
A131569E01
  1. Remove the instrument panel junction block (main body ECU).

  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E19-5 (IG2D) - Relay block IG2 relay terminal 1
    Below 1 Ω
    Relay block IG2 relay terminal 2 - Body ground
    Below 1 Ω
    E19-5 (IG2D) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU.

  1. Reinstall the IG2 relay.



NG
CHECK ENTRY AND START SYSTEM
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR

10. CHECK WIRE HARNESS (IGNITION SWITCH - ENGINE ROOM NO. 1 RELAY BLOCK)
A131570E01
  1. Disconnect the E5 ignition switch connector.

  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E5-6 (IG2) - Relay block IG2 relay terminal 1
    Below 1 Ω
    Relay block IG2 relay terminal 2 - Body ground
    Below 1 Ω
    E5-6 (IG2) - Body ground
    10 kΩ or higher

  1. Reconnect the ignition switch connector.

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


11. INSPECT IGNITION SWITCH ASSEMBLY

  1. A131560E01
    Disconnect the E5 ignition switch connector.

  1. Measure the resistance of the terminals shown below.

    Standard resistance:
    Condition
    Tester Condition
    Specified Condition
    OFF
    Between all terminals
    1 MΩ or more
    ACC
    2 - 3
    1 Ω or less
    ON
    2 - 4, 6 - 7
    1 Ω or less
    START
    1 - 2, 2 - 4, 6 - 7, 7 - 8
    1 Ω or less

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE IGNITION SWITCH ASSEMBLY


← ECM Power Source Circuit (Nov 2005 – Dec 2006)VC Output Circuit (from Nov 2005) →