VC Output Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK MIL CONDITION |
Check that Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch on (IG).
- OK:
- MIL lights up
|
|
||||
| NG | |
| 2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Check the communication between the tester and ECM.
- Result:
Result
Proceed to
Communication is possible
A
Communication is not possible
B
|
|
||||
| B | |
| 3. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the A6 accelerator pedal position sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| B | |
| 4. CHECK MIL (BATTERY CURRENT SENSOR) |
Disconnect the B31 battery current sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the battery current sensor connector.
|
|
||||
| B | |
| 5. CHECK MIL (FUEL PRESSURE SENSOR) |
Disconnect the B60 fuel pressure sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the fuel pressure sensor connector.
|
|
||||
| B | |
| 6. CHECK MIL (EGR VALVE POSITION SENSOR) |
Disconnect the B54 EGR valve position sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the EGR valve position sensor connector.
|
|
||||
| B | |
| 7. CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the B55 throttle position sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the throttle position sensor connector.
|
|
||||
| B | |
| 8. CHECK MIL (DIFFERENTIAL PRESSURE SENSOR) |
Disconnect the B61 different pressure sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the different pressure sensor connector.
|
|
||||
| B | |
| 9. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
Disconnect the B45 manifold absolute pressure sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the manifold absolute pressure sensor connector.
|
|
||||
| B | |
| 10. CHECK WIRE HARNESS (EACH SENSOR - BODY GROUND) |
Disconnect the A6 accelerator pedal position sensor connector.
Disconnect the B31 battery current sensor connector.
Disconnect the B60 fuel pressure sensor connector.
Disconnect the B54 EGR valve position sensor connector.
Disconnect the B55 throttle position sensor connector.
Disconnect the B61 different pressure sensor connector.
Disconnect the B45 manifold absolute pressure sensor connector.
Disconnect the A12 and B32 ECM connectors.

Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A12-55 (VCPA) - Body ground
10 kΩ or higher
A12-56 (VCP2) - Body ground
10 kΩ or higher
B32-70 (VCIB) - Body ground
10 kΩ or higher
B32-68 (VCS) - Body ground
10 kΩ or higher
B32-69 (VCM) - Body ground
10 kΩ or higher
B32-72 (VCEG) - Body ground
10 kΩ or higher
B32-73 (VCVL) - Body ground
10 kΩ or higher
B32-74 (VCPX) - Body ground
10 kΩ or higher
B32-71 (VCPM) - Body ground
10 kΩ or higher
Reconnect the accelerator pedal position sensor connector.
Reconnect the battery current sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the EGR valve position sensor connector.
Reconnect the throttle position sensor connector.
Reconnect the different pressure sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the ECM connectors.
|
|
||||
| OK | ||
| ||
