Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for RHD)
REMOVAL
Removal / installation · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column
(Click here ).
1.
PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
3.
REMOVE STEERING PAD
Straighten the front wheels.
Using a T30 "torx" driver, loosen the 2 screws until the groove along each screw circumference catches on the screw case.
Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.
NOTICE:
When removing the steering pad, do not pull the airbag wire harness.
Using a screwdriver, disconnect the 2 airbag connectors.
CAUTION:
When handling the airbag connector, do not damage the airbag wire harness.
Disconnect the horn connector and remove the steering pad.
4.
REMOVE STEERING WHEEL ASSEMBLY
Remove the nut and place matchmarks on the steering wheel and steering column.
Using SST, remove the steering wheel.
SST
09950-50013
(09951-05010, 09952-05010, 09953-05020, 09954-05021)
NOTICE:
Apply a small amount of grease to the threads and tip of SST (center bolt) before use.
5.
REMOVE STEERING COLUMN COVER
Detach the 4 claws, release the tilt lever and remove the steering column cover lower.
Detach the claw and remove the steering column cover upper.
6.
REMOVE SPIRAL CABLE SUB-ASSEMBLY
Disconnect all connectors from the turn signal switch with spiral cable.
7.
REMOVE COMBINATION SWITCH ASSEMBLY
Detach the clamp indicated by the arrow in the illustration and remove the combination switch from the steering column.
8.
REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
Remove the instrument panel (Click here ).
9.
DISCONNECT POWER STEERING ECU
Detach the power steering motor wire harness and torque sensor wire harness clamps from the power steering ECU side.
Disconnect the 2 steering column connectors from the power steering ECU.
10.
REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Remove the 2 screws.
Detach the 2 claws and remove the instrument panel under cover.
11.
REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)
Remove the 4 bolts and driver side knee airbag.
Disconnect the connector.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
12.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)
Remove the 2 screws.
Using a screwdriver, detach the 8 claws and remove the lower instrument panel finish panel.
HINT:
Tape the screwdriver tip before use.
13.
REMOVE COLUMN HOLE COVER SILENCER SHEET
Turn back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.
14.
REMOVE AIR DUCT
15.
REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
Place matchmarks on the steering intermediate shaft and steering gear.
Remove bolt A and detach the steering intermediate shaft from the steering gear.
Place matchmarks on the steering intermediate shaft and steering column.
Remove bolt B and detach the steering intermediate shaft from the steering column.
16.
REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
Remove the brake pedal support (Click here ).
17.
REMOVE STEERING COLUMN ASSEMBLY
Disconnect all connectors and detach all wire harness clamps from the steering column.
Remove the bolt and 2 nuts and remove the steering column from the instrument panel reinforcement.