2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL FAN SHROUD

A128581
  1. Attach the pawl fittings of the shroud.

  1. Install the fan shroud with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


2. INSTALL OUTLET RADIATOR HOSE

A127742
  1. Install the outlet radiator hose to the radiator.

  1. A127748E01
    Position the clip as illustrated.


3. INSTALL INLET RADIATOR HOSE

A127743E01
  1. Install the inlet radiator hose and No. 5 water by-pass hose to the radiator.

  1. A128580E01
    Position clips A and B as illustrated.


4. INSTALL RADIATOR AND INTERCOOLER

NOTICE:
When reusing the air hose or air tube, check that there is no damage and foreign objects. If necessary, clean it.

  1. A123563E01
    Align the intercooler with the radiator, and then install the intercooler to the radiator with the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the No. 2 air tube to the intercooler and No. 3 air hose.

  1. Install the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A123567E01
    Tighten the 2 clamps as shown in the illustration.

  1. A123568E01
    Install the No. 2 air hose to the intercooler. Tighten the clamp as shown in the illustration.

  1. Install the radiator (with intercooler) to the vehicle.

  1. Connect the No. 2 and No. 3 air hoses to the engine.

  1. A123564E01
    Tighten the 2 clamps as shown in the illustration.


5. CONNECT OUTLET RADIATOR HOSE

A126847E01
  1. Connect the outlet radiator hose to the engine.

  1. A127749E01
    Position the clip as illustrated.


6. CONNECT INLET RADIATOR HOSE

A126848E01
  1. Connect the inlet radiator hose to the engine.

  1. A127747E01
    Position the clip as illustrated.


7. INSTALL RADIATOR SUPPORT UPPER

A127758
  1. Install the radiator support upper with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


8. INSTALL COOLER CONDENSER ASSEMBLY

  1. E126558
    Install the cooler condenser.


9. INSTALL NO. 1 RADIATOR SUPPORT

E126557
  1. Install the 2 radiator supports with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


10. INSTALL RADIATOR SUPPORT UPPER BRACKET

E126555
  1. Install the 2 brackets with the 2 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


11. INSTALL HOOD LOCK ASSEMBLY (for LHD)

  1. B127328E01
    Connect the cable to the lock.

  1. Install the lock with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Adjust the lock.

  1. w/ Hood courtesy switch:
    Connect the connector.


12. INSTALL HOOD LOCK ASSEMBLY (for RHD)

  1. B127327
    Connect the cable to the lock.

  1. B127328E01
    Install the lock with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Adjust the lock.

  1. w/ Hood courtesy switch:
    Connect the connector.


13. INSTALL NO. 1 WATER BY-PASS HOSE

A126842E01
  1. Connect the No. 1 water by-pass hose to the radiator and radiator reservoir.

  1. A128579E01
    Position clips A and B as illustrated.

  1. Install the No. 1 water by-pass hose with the 2 bolts to the radiator support upper.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the No. 1 water by-pass hose to the hose clamp.


14. CONNECT COOLING FAN MOTOR HARNESS

A127759
  1. Attach the harness with the 7 clamps.

  1. Connect the 4 connectors.


15. INSTALL BATTERY BRACKET REINFORCEMENT

  1. A124919
    Install the bracket reinforcement with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


16. INSTALL FRONT BATTERY BRACKET

  1. A124918
    Install the front bracket with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Attach the 2 wire harness clamps.


17. INSTALL BATTERY

18. INSTALL BATTERY CLAMP

  1. A124917E01
    Attach the hook of the battery clamp to the front battery bracket.

  1. Temporarily tighten the nut and install the bolt.

  1. Adjust the battery clamp's position.

  1. Fully tighten the nut and bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the 2 wire harness clamps.


19. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY UPPER
  1. Install the reinforcement and install the 2 bolt.

  1. Connect the 2 horns connectors.


20. INSTALL FRONT BUMPER
  1. Install the front bumper (Click here).


21. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

  1. A126841E01
    Continue adding TOYOTA SLLC until it is filled to the B line.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard capacity:
    Item
    Specified Condition
    w/o Combustion Type Power Heater
    7.3 liters
    (7.7 US qts, 6.4 Imp. qts)
    w/ Combustion Type Power Heater
    7.7 liters
    (8.1 US qts, 6.8 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine, and warm it up until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Specified Condition
      Manual Air Conditioning System
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Automatic Air Conditioning System
      Temperature - Toward MAX
      Air conditioning switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Until the coolant level has stabilized, run the engine at 2,000 rpm.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

  1. A126840
    Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.


22. CHECK FOR ENGINE COOLANT LEAKS
  1. Remove the radiator reservoir cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A128571E01
    Fill the radiator with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 137 kPa (1.4 kgf/cm2, 19 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.


23. INSTALL ENGINE UNDER COVER REAR LH
  1. Install the under cover with the 2 clips.


24. INSTALL ENGINE UNDER COVER REAR RH
  1. Install the engine under cover with the 2 clips.


25. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the engine under cover with the 12 clips and 4 bolts.


26. INSTALL NO. 1 ENGINE COVER

  1. A123518
    Attach the 4 clips to install the engine cover.


27. INSTALL RADIATOR SUPPORT OPENING COVER

  1. B130259
    Install the 2 clips.


28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

29. CHARGE REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    430 +-30 g (15.2 +-1.1 oz.)

    SST
    07110-58060   (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.


30. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch ON after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


31. CHECK FOR REFRIGERANT LEAKS
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the gas leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E12
    Using a gas leak detector, check the refrigerant line for leakage.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and leave the pressure switch on for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.

← INSTALLATION (Nov 2005 – Dec 2006)INSTALLATION (from Aug 2007) →