2005-2008 RAV4 · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008

CAUTION:
Wear protective gloves. Sharp areas on the seat frame (with adjuster) may injure your hands.


1. INSTALL FRONT SEAT WIRE

2. INSTALL SEAT POSITION AIRBAG SENSOR
  1. Using a 1 mm (0.039 in.) feeler gauge, install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm to 1.4 mm (0.023 to 0.055 in.).

  1. Using a T30 "torx" socket, tighten the "torx" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm to 1.4 mm (0.023 to 0.055 in.).

  1. Connect the connector.

  1. B127917E03
    Install the seat slide position sensor protector to the seat position sensor.


3. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

  1. B131284
    Install the lumbar support adjuster with the 2 screws.

  1. Connect the connector.


4. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

  1. B122088
    Attach the hook of the lower shield.

  1. Install the lower shield with the screw.


5. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH

HINT:
Use the same procedures described for the LH side.


6. INSTALL RECLINING ADJUSTER UPPER INSIDE COVER LH

  1. B131286
    Install the inside cover with the screw.


7. INSTALL RECLINING ADJUSTER UPPER INSIDE COVER RH
  1. Install the inside cover with the screw.


8. INSTALL RECLINING ADJUSTER LOWER INSIDE COVER LH

  1. B131285
    Attach the claw to install the inside cover.

  1. Install the 2 screws.


9. INSTALL RECLINING ADJUSTER LOWER INSIDE COVER RH

HINT:
Use the same procedures described for the LH side.


10. INSTALL FRONT SEATBACK HEATER (w/ Seat Heater System)

  1. B131243E01
    Using a tacker, install the seatback heater to the end of the seat cover with 6 new tack pins.

    NOTICE:
    Do not substitute other metal parts for tack pins.


11. INSTALL FRONT SEATBACK COVER

NOTICE:

  1. B131242E01
  2. Be careful not to damage the cover.
  3. When installing the hog rings, avoid wrinkling the cover.

  1. Using hog ring pliers, install the seatback cover to the seatback pad with 11 new hog rings.

  1. Install the seatback cover (with pad) to the seat frame (with adjuster).

  1. B131236
    Fully cover the airbag with the 2 seatback cover brackets and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. B060977E01
    Attach the 4 claws to install the 2 headrest supports.

  1. B131240E01
    Attach the hooks.

  1. Using hog ring pliers, install the seatback cover (with pad) with 5 new hog rings.


12. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

  1. B131246
    Push the seatback board in the direction indicated by the arrow in the illustration to attach the 2 claws.

  1. B131245
    Open the lower part of the seatback board. Then install the seatback board with the 2 screws.


13. INSTALL FRONT SEAT CUSHION HEATER (w/ Seat Heater System)

  1. B134550E01
    Using a tacker, install the seat cushion heater to the end of the seat cover with 10 new tack pins.

    NOTICE:
    Do not substitute other metal parts for tack pins.


14. INSTALL FRONT SEAT CUSHION COVER

  1. B131233E01
    Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the seat cushion cover (with pad) to the seat frame (with adjuster).

  1. B131230E01
    Attach the hooks and install the 2 clips.

  1. w/ Seat Heater System:
    Connect the connector.


15. INSTALL FRONT POWER SEAT SWITCH
  1. Connect the connector.

  1. B131280
    Install the switch with the 3 screws.


16. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

B133641E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.

  1. for Driver Seat:
    Attach the 2 clamps and connect the 2 connectors.

  1. for Passenger Seat:
    Attach the 2 clamps and connect the 2 connectors.


17. INSTALL FRONT SEAT CUSHION INNER SHIELD LH

  1. B131278
    Attach the clip and 3 claws to install the inner shield.

  1. Install the screw.


18. INSTALL FRONT POWER SEAT LUMBAR SWITCH

  1. B131279
    Install the switch to the cushion shield with the 2 screws.


19. INSTALL FRONT SEAT CUSHION SHIELD LH

  1. B131276
    Install the front No. 1 seat cushion inner shield to the cushion shield.

    1. Attach the claw to install the front No. 1 seat cushion inner shield.

    2. Install the screw.

  1. Connect the connector to the front power seat lumbar switch.

  1. B131275
    Attach the 3 claws and install the cushion shield (with front No. 1 seat cushion inner shield) to the seat frame (with adjuster).

  1. Install the 5 screws.

  1. B131222
    Connect the 2 rubber bands of the front seatback board to the seat frame (with adjuster).


20. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

21. INSTALL RECLINING POWER SEAT SWITCH KNOB
← DISASSEMBLY (from Aug 2008)REASSEMBLY (Jan 2007 – Jul 2008) →