2005-2008 RAV4 · Service Manual ENGINE

Pre-heating Control Circuit

Circuit diagnosis · Vehicles built from Aug 2007

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval of the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned on (IG). The ECM then turns on the glow plug relay and permits the current to flow through the glow plug based on the ECM's calculated time. The glow plug relay is then heated, and enhances fuel combustion with a cold engine.
This DTC will be set if the glow plug or the circuit is open.
A129368E01

HINT:
  1. These troubleshooting procedures are for: 1) difficult starting engine in cold weather, and 2) difficulty driving / vehicle malfunctions in cold weather immediately after engine is started.
  2. After the engine is started, the ECM performs an "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.

A117830E03

WIRING DIAGRAM

A159652E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK TERMINAL VOLTAGE (GREL TERMINAL)

  1. A131566E04
    Remove the glow plug relay.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    B43-2 - Body ground
    9 to 14 V

  1. Reinstall the glow plug relay.



NG
Go to step 7
OK


2. INSPECT GLOW PLUG RELAY
  1. Remove the glow plug relay.

  1. A130325E02
    Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    10 kΩ or higher
    3 - 4
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)

  1. Reinstall the glow plug relay.



NG
REPLACE GLOW PLUG RELAY
OK


3. INSPECT GLOW FUSE

  1. A130321E01
    Remove the GLOW fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the GLOW fuse.



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


4. INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

  1. E110714
    Disconnect the glow plug wire.

  1. Measure the resistance of the glow plugs.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Glow plug terminal - Body ground
    20°C (68°F)
    Approximately 0.95 Ω

    HINT:
    If any of the glow plugs has an open circuit, the engine power will be insufficient only when the engine is cold.

    NOTICE:
    1. Exercise extreme care not to damage the glow plug pipes. Damaging them could cause an open circuit, or shorten the life of the glow plugs.
    2. Keep the glow plugs free of oil and fuel while cleaning.
    3. Wipe any oil off of the terminal and Bakelite washer with a clean, dry cloth during inspection.
    4. Do not apply more than 11 V to the glow plugs as it may cause an open circuit.

  1. Reconnect the glow plug wire.



NG
REPLACE GLOW PLUG ASSEMBLY
OK


5. CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
  1. Check the glow plug installation.

    OK:
    Glow plugs are installed securely.

Torque:
12.3 N*m{ 125 kgf*cm , 9 ft.*lbf }



NG
TIGHTEN GLOW PLUG
OK


6. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY- GLOW PLUG - BATTERY AND BODY GROUND)

  1. A131566E04
    Remove the glow plug relay.

  1. Disconnect the glow plug connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    B43-3 - B49-1
    Below 1 Ω
    B43-4 - Positive (+) battery terminal cabled
    Below 1 Ω
    B43-1 - Body ground
    Below 1 Ω

  1. Reinstall the glow plug relay.

  1. Reconnect the glow plug connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS

7. CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)

  1. A130157E03
    Remove the glow plug relay.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B43-2 - B32-56 (GREL)
    Below 1 Ω
    B32-56 (GREL) - Body ground
    10 kΩ or higher

  1. Reinstall the glow plug relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← Pre-heating Control Circuit (Jan 2007 – Jul 2007)Rough Idling or Excessive Engine Vibrations (Jan 2007 – Jul 2007) →