Lack of Power or Hesitation
Circuit diagnosis · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
| Malfunction Condition |
Main Trouble Areas |
Related Trouble Areas |
|
|
|
- HINT:
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
- Check that the vehicle has not been modified in any way prior to the vehicle inspection.
- This troubleshooting procedure checks for the cause of an obvious lack of engine power (the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.
- Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
INSPECTION PROCEDURE
- NOTICE:
- After replacing the supply pump, the ECM needs initialization (Click here).
- After replacing the injector, the ECM needs registration (Click here).
- After replacing the supply pump, the ECM needs initialization (Click here).
- HINT:
- Before troubleshooting, conduct the following:
- Check the fuel quality.
- Check the fuel for air.
- Check the fuel system for blockages.
- Check the air filter.
- Check the engine oil.
- Check the engine coolant.
- Check the engine idling speed and the maximum engine speed.
- Check the vacuum pump.
- Before troubleshooting, conduct the following:
| 1. CHECK WIRE HARNESS AND CONNECTOR IN ENGINE ROOM |
Check the wire harness and connector connections of common rail system components.
- HINT:
- Check the following components and system:
- Sensors
- Supply pump
- Common rail
- Injectors
- EDU
- Turbocharger system
- Intake and exhaust system
- Sensors
- OK:
- The wire harnesses and connectors are connected securely.
|
|
||||
| OK | |
| 2. PERFORM CONFIRMATION DRIVING PATTERN |
- HINT:
- Drive the vehicle according to the driving pattern below to allow the ECM to set DTCs relating to malfunctions of the fuel system, EGR system, and throttle valve. If DTC are set, problem areas can be identified.
Enter CHECK MODE (Click here).
Fully warm up the engine.
Allow the engine to idle for 5 minutes or more.
Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (procedure "A").
Decelerate and stop the vehicle (procedure "B").
Repeat procedure "A" and procedure "B" 4 times or more.
Stop the engine and wait for at least 10 seconds (procedure "C").
Repeat procedure "A" and procedure "C" described above to set DTCs relating to the EGR system and throttle valve.
Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to set DTCs relating to the supply pump).
| NEXT | |
| 3. READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
- Result:
Display (DTC Output)
Proceed to
No DTCs
A
Engine related DTCs
B
|
|
||||
| A | |
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK) |
- HINT:
- By performing this Active Test, the engine speed is maintained at 2,000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.
Visually check the supply pump, injector and fuel line located between the supply pump and common rail for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail and the injector.
- HINT:
- There may be fuel leaks inside the components, such as the supply pump.
- OK:
- No leakage.
|
|
||||
| OK | |
| 5. CHECK WHITE SMOKE |
Rev up the engine from idling to 3,000 rpm several times to check whether white smoke is emitted from the exhaust pipe.
Check that the intake system pipes and hoses are not excessively contaminated with oil.If white smoke is emitted from the intake system, its pipes and hoses are excessively contaminated with oil. If the presence of white smoke in the exhaust gas is confirmed, there is a high possibility of mechanical problems in the turbocharger or engine.
- Result:
Result
Proceed to
No problems described above
A
White smoke emitted, or intake system pipes and hoses excessively contaminated with oil
B
|
|
||||
| A | |
| 6. READ VALUE USING MANIFOLD ABSOLUTE PRESSURE SENSOR, MAF METER AND FUEL PRESSURE SENSOR (MAP AND FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Select the following menu items in order and read the values.
- MAP
- MAF
- Fuel Press
- Standard value:
Item
Engine Speed*1
Standard Range
Description
MAP*2
Ignition switch on (IG) (engine stopped)
Same as atmospheric pressure
Intake manifold internal pressure detected by manifold absolute pressure sensor
Idling
93 to 101 kPa (697 to 758 mmHg, 27.46 to 29.83 in.Hg)
3,000 rpm (no engine load)
110 to 130 kPa (825 to 975 mmHg, 32.48 to 38.39 in.Hg)
3,000 rpm (driving with full throttle acceleration)*5
234 to 254 kPa (1,755 to 1,905 mmHg, 69.10 to 75.01 in.Hg)
3600 rpm (driving with full throttle acceleration)*5
234 to 254 kPa (1,755 to 1,905 mmHg, 69.10 to 75.01 in.Hg)
MAF*2, *4
Ignition switch on (IG) (engine stopped)
0 g/sec.
Intake air volume detected by mass air flow meter
Idling
3.5 to 8.5 g/sec.
3,000 rpm (no engine load)
29 to 49 g/sec.
3,000 rpm (driving with full throttle acceleration)*5
123 to 143 g/sec.
3,600 rpm (driving with full throttle acceleration)*5
153 to 163 g/sec.
Common Rail Pressure*3
Idling
35 to 40 MPa
Common rail internal fuel pressure
2,000 rpm (no engine load)
65 to 78 MPa
3,000 rpm (no engine load)
78 to 88 MPa
3,000 rpm (driving with full throttle acceleration)*5
140 to 150 MPa
3,600 rpm (driving with full throttle acceleration)*5
165 to 170 MPa
- Result:
Item
Result
Proceed to
MAP, MAF, and Fuel press
Standard range
A
MAP and MAF
Outside standard range
B
Only MAP
Outside standard range
C
Only MAF
Outside standard range
D
Only Fuel Press
Outside standard range
E
- HINT:
- *1: The A/C switch and all accessory switches should be OFF with a fully warm engine.
- *2: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the stable boost pressure is maintained for approximately 10 seconds.
- *3: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the vehicle is accelerated for approximately 10 seconds.
- *4: When the mass air flow meter malfunctions, the MAF output may deviate from the standard (referential) range when the engine idles and is accelerated from 3,000 to 4,000 rpm with full throttle acceleration.
- *5: Fully depress the accelerator pedal with the vehicle creeping at idle speed in 2nd gear.
- MAP
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 7. READ VALUE USING INJECTOR (INJECTION FEED BACK VAL AND INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine, warm it up, and turn the tester ON.
Select the following menu items in order and read the values.
- Injection Feedback Val #1, #2, #3, and #4
- Injection Volume
- Standard value:
Item
Engine Speed*
Standard Range
Description
Injection Feedback Val #1
Idling
-3.5 to 3.5 mm3
Value of injector fuel injection volume compensates for differences in combustion condition of cylinders - Positive values indicate control which corrects combustion degradation
- Negative values indicate control which corrects excessive combustion pressure
- If problems exist, "Injection Feedback Val" may deviate from the -3.0 and 3.0 mm3 range
Injection Feedback Val #2
Idling
-3.5 to 3.5 mm3
Injection Feedback Val #3
Idling
-3.5 to 3.5 mm3
Injection Feedback Val #4
Idling
-3.5 to 3.5 mm3
Injection Volume
Idling
4.5 to 9.0 mm3
Fuel injection volume value controlled by ECU - Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, boost pressure, atmospheric pressure, and EGR volume
- If problems exist, "Injection Volume" may be outside the standard range
- Positive values indicate control which corrects combustion degradation
- Result:
Result
Proceed to
Standard range
A
Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range
B
- HINT:
- *: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.
- Injection Feedback Val #1, #2, #3, and #4
|
|
||||
| A | |
| 8. CHECK INJECTOR COMPENSATION CODE |
Read the injector compensation code (Click here).
- HINT:
- If the injector compensation code is not correctly registered, it may cause malfunctions (Click here).
Check the injector compensation code.
- OK:
- Compensation code of the installed injector is the same as the one registered in the ECM.
|
|
||||
| OK | |
| 9. RESET ECM |
Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.
Reconnect the cable to the negative (-) battery terminal.
Check whether the malfunction has been successfully repaired by performing a driving test using the freeze frame data recorded at the time the malfunction occurred.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| NG | |
| 10. BLEED AIR FROM FUEL SYSTEM |
To bleed air from the priming pump, pump the priming pump until it becomes hard and cannot be pumped any more.
| NEXT | |
| 11. CONFIRM WHETHER LACK OF POWER HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the lack of power has been successfully repaired by performing a driving test. Use the freeze frame data recorded at the time the malfunction occurred.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| NG | |
| 12. INSPECT GLOW PLUG ASSEMBLY |
Disconnect the glow plug wire.

Measure the resistance of the glow plug.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Glow plug terminal - Body ground
20°C (68°F)
Approximately 0.95 Ω
- HINT:
- If any one of the glow plugs has an open malfunction, the engine power is insufficient only when the engine is cold.
- NOTICE:
- Be careful not to damage the glow plug pipes. Damaging them could cause an open circuit, or shorten the life of the glow plugs.
- Keep the glow plug free of oil and fuel while cleaning.
- Wipe any oil off the terminal and Bakelite washer with a clean, dry cloth during inspection.
- Do not apply more than 11 V to the glow plug as it could cause an open circuit.
- Be careful not to damage the glow plug pipes. Damaging them could cause an open circuit, or shorten the life of the glow plugs.
Reconnect the glow plug wire.
|
|
||||
| OK | |
| 13. CHECK INTAKE SYSTEM |
Check for air leakage and blockage between the air cleaner and turbocharger.
Check for air leakage and blockage between the turbocharger and intake manifold.
- OK:
- No leakage or blockage.
| NEXT | ||
| ||
| 14. IDENTIFY MALFUNCTIONING CYLINDER INJECTOR |
Follow the instructions in the table below according to the check result of the intelligent tester.
- HINT:
- This operation is based on the premise that the common rail pressure is normal.
- Standard value:
Item
Engine Speed*
Reference Value
Injection Feedback Val #1 to #4
Idling
-3.5 to 3.5 mm3
Injection Volume
Idling
4.5 to 9.0 mm3
- HINT:
- *: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.
- Result:
Injection Volume
Injection Volume
Injection Feedback Val #1 to #4
Less than 3.0 mm3
Between 3.0 to 10.0 mm3 (Normal)
More than 10.0 mm3
3.5 mm3 or more, -3.5 mm3 or less
A
B
B
Between -3.5 to 3.5 mm3
-
Normal
C*
Proceed to
Proceed to
Descriptions
A
Inspect and repair cylinder injector with revised injection volume of less than -3.0 mm3: - Perform power balance inspection and identify malfunctioning cylinder
- Replace malfunctioning cylinder injector
Abnormal value cylinder injector injects excessively large quantity of fuel
B
Identify malfunctioning cylinders by conducting power balance inspection: - Perform power balance inspection to identify malfunctioning cylinders
- Clean malfunctioning cylinder injector, check, and repair it
Abnormal value cylinder injector injects excessively small quantity of fuel: - Fuel injection volume too low due to injector nozzle being blocked by deposits
- Abnormal value cylinder injector compression decreases
- Abnormal value cylinder injector injects excessively large quantity of fuel
C
Inspect and repair all cylinder injectors:
Clean all cylinder injectors, inspect, and repair them
All cylinder injectors inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector nozzles being blocked by deposits
- Perform power balance inspection and identify malfunctioning cylinder
- HINT:
- *: When the Injection Volume displayed on the tester is large despite the Fuel Pressure and Injection Feedback Val #1 to #4 in the Data List being normal, the injector may be clogged. In this case, there may be deposits inside or outside the tip of the injector.
- Despite the injector functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).
- Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.
- Despite the injector functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).
|
|
||||
|
|
||||
| A | |
| 15. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3, and #4 Fuel Cut.
Check the four cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.
- HINT:
- If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
- If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
- If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
| NEXT | ||
| ||
| 16. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3, and #4 Fuel Cut.
Check the four cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.
- HINT:
- If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
- If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
- If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
| NEXT | |
| 17. CHECK CYLINDER COMPRESSION PRESSURE |
Check the cylinder compression pressure (Click here).
- Standard pressure:
- 2,700 kPa (27.5 kgf/cm2, 392 psi)
- Minimum pressure:
- 2,200 kPa (22.4 kgf/cm2, 319 psi)
- Difference between each cylinder:
- 500 kPa (5.1 kgf/cm2, 73 psi)
|
|
||||
| OK | |
| 18. CHECK MALFUNCTIONING CYLINDER'S INJECTOR FOR DEPOSITS |
- HINT:
- If an injector is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.
Check the injector for any deposits.
- Result:
Injector Condition
Proceed to
Deposits
A
No deposits
B
|
|
||||
| A | |
| 19. CLEAN INJECTOR |
Wipe away deposits from the tips of the injectors.
- HINT:
- Solvent or carbon removal agents help remove the deposits easily.
- Exercise extreme care not to damage the injectors while wiping off the deposits.
- Solvent or carbon removal agents help remove the deposits easily.
| NEXT | |
| 20. READ VALUE USING INJECTOR (INJECTION FEEDBACK VAL AND INJECTION VOLUME) |
Reinstall the injector to the cylinder head.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Select the following menu items in order and read the values.
- Injection Feedback Val #1, #2, #3, and #4
- Injection Volume
- Standard value:
Item
Engine Speed*
Reference Value
Injection Feedback Val #1 to #4
Idling
-3.5 to 3.5 mm3
Injection Volume
Idling
4.5 to 9.0 mm3
- HINT:
- The A/C switch and all accessory switches should be OFF with a fully warm engine.
- When the values are outside the standard range, deposits inside the injector may be causing the problem.
- The A/C switch and all accessory switches should be OFF with a fully warm engine.
- OK:
- Values are within the standard range.
- Injection Feedback Val #1, #2, #3, and #4
|
|
||||
| OK | ||
| ||
| 21. CHECK INJECTORS FOR DEPOSITS (EXCEPT FUEL ADDITION INJECTOR) |
- HINT:
- If an injector is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.
Check the injector for any deposits.
- Result:
Injector Condition
Proceed to
Deposits
A
No deposits
B
|
|
||||
| A | |
| 22. CLEAN INJECTOR |
Wipe away deposits from the tips of the injectors.
- HINT:
- Solvent or carbon removal agents help remove the deposits easily.
- Exercise extreme care not to damage the injectors while wiping off the deposits.
- Solvent or carbon removal agents help remove the deposits easily.
| NEXT | |
| 23. READ VALUE USING INJECTOR (INJECTION FEEDBACK VAL AND INJECTION VOLUME) |
Reinstall the injector to the cylinder head.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Select the following menu items in order and read the values.
- Injection Feedback Val #1, #2, #3, and #4
- Injection Volume
- Standard value:
Item
Engine Speed*
Reference Value
Injection Feedback Val #1 to #4
Idling
-3.5 to 3.5 mm3
Injection Volume #1 to #4
Idling
4.5 to 9.0 mm3
- HINT:
- *: The A/C switch and all accessory switches should be OFF with a fully warm engine.
- When the values are outside the standard range, deposits inside the injector may be causing the problem.
- *: The A/C switch and all accessory switches should be OFF with a fully warm engine.
- OK:
- Values are within the standard range.
- Injection Feedback Val #1, #2, #3, and #4
|
|
||||
| OK | ||
| ||
| 24. CHECK EGR VALVE ASSEMBLY |
Check the EGR valve assembly (Click here).
|
|
||||
| OK | |
| 25. INSPECT DIESEL THROTTLE BODY ASSEMBLY |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and tester ON.
Enter the following menus: Powertrain / Engine and ECT / Diesel Throttle Angle.
Read the value.
- Standard value:
- Ignition switch on (IG):
- 0%
- Idling (Warmed up engine):
- 95%
- Accelerator pedal fully depressed:
- 0%
|
|
||||
| OK | |
| 26. CHECK INTAKE SYSTEM |
Check for air leakage and blockage between the air cleaner and turbocharger.
Check for air leakage and blockage between the turbocharger and intake manifold.
- OK:
- No leakage or blockage.
|
|
||||
| OK | |
| 27. CHECK TURBOCHARGER SUB-ASSEMBLY (MECHANICAL PROBLEM) |
Disconnect the air cleaner hose.
Use a mirror to visually check the turbocharger for any mechanical problems.
When the engine is cold, check that the impeller of the turbocharger rotates smoothly, and perform a contact check to confirm if it is damaged.
- OK:
- Impeller rotates smoothly and is not damaged.
Reconnect the air cleaner hose.
|
|
||||
| OK | |
| 28. CHECK VACUUM HOSE (TURBOCHARGER - VRV, VRV - VACUUM PUMP) |
Check that the vacuum hoses are installed correctly.
Check the vacuum hoses for any cracks and damage.
Check the vacuum hoses for air leaks and any blockage.
- OK:
- The vacuum hoses are correctly connected.
|
|
||||
| OK | |
| 29. CHECK VRV FOR TURBOCHARGER CONTROL |
Check the VRV (Click here).
|
|
||||
| OK | |
| 30. INSPECT TURBOCHARGER ACTUATOR |
Inspect the actuator.
- OK:
- The valve has no contamination and it moves smoothly.
|
|
||||
| OK | |
| 31. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Select the following menu items in order and read the values.
- MAP
- MAF
- Standard value:
Item
Engine Speed*1
Standard Range
Description
MAP*2
Ignition switch on (IG) (engine stopped)
Same as atmospheric pressure
Intake manifold internal pressure detected by manifold absolute pressure sensor
Idling
93 to 101 kPa (697 to 758 mmHg, 27.46 to 29.83 in.Hg)
3,000 rpm (no engine load)
110 to 130 kPa (825 to 975 mmHg, 32.48 to 38.39 in.Hg)
3,000 rpm (driving with full throttle acceleration)*5
234 to 254 kPa (1,755 to 1,905 mmHg, 69.10 to 75.01 in.Hg)
3600 rpm (driving with full throttle acceleration)*5
234 to 254 kPa (1,755 to 1,905 mmHg, 69.10 to 75.01 in.Hg)
MAF*2, *4
Ignition switch on (IG) (engine stopped)
0 g/sec.
Intake air volume detected by mass air flow meter
Idling
3.5 to 8.5 g/sec.
3,000 rpm (no engine load)
29 to 49 g/sec.
3,000 rpm (driving with full throttle acceleration)*5
123 to 143 g/sec.
3,600 rpm (driving with full throttle acceleration)*5
153 to 163 g/sec.
Common Rail Pressure*3
Idling
35 to 40 MPa
Common rail internal fuel pressure
2,000 rpm (no engine load)
65 to 78 MPa
3,000 rpm (no engine load)
78 to 88 MPa
3,000 rpm (driving with full throttle acceleration)*5
140 to 150 MPa
3,600 rpm (driving with full throttle acceleration)*5
165 to 170 MPa
- HINT:
- *1: The A/C switch and all accessory switches should be OFF with a fully warm engine.
- *2: This value is indicated when the ambient temperature is 25°C (77°F), the atmospheric pressure is 101 kPa (758 mmHg, 29.83 in.Hg), and the stable boost pressure is maintained for approximately 10 seconds.
- *3: When the mass air flow meter malfunctions, the MAF output may deviate from the standard (referential) range when the engine idles and is accelerated from 3,000 to 4,000 rpm with full throttle acceleration.
- *4: Fully depress the accelerator pedal with the vehicle creeping at idle speed in 2nd gear.
- OK:
- The values are within the standard range.
- MAP
|
|
||||
| OK | ||
| ||
| 32. CHECK AND REPLACE FUEL FILTER ASSEMBLY |
| NEXT | |
| 33. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up, and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Select the following menu item and read the values.
- Fuel Press
- Standard value:
Item
Engine Speed*
Reference Value
Fuel Press
Idling
35 to 40 MPa
Fuel Press
2,000 rpm (no engine load)
65 to 78 MPa
Fuel Press
3,000 rpm (no engine load)
78 to 88 MPa
Fuel Press
3,600 rpm (driving with full throttle acceleration)
165 to 170 MPa
- HINT:
- *: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.
- OK:
- The values are within the standard range.
- Fuel Press
|
|
||||
| NG | |
| 34. INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR) |
Disconnect the B60 fuel pressure sensor connector.

Measure the resistance of each terminal of the fuel pressure sensor.
- Standard resistance:
Tester Connection
Specified Condition
B60-2 (PR) - B60-1 (E2)
16.4 kΩ or less
B60-2 (PR) - B60-3 (VC)
3 kΩ or less
Reconnect the fuel pressure sensor connector.
|
|
||||
| OK | |
| 35. INSPECT SUPPLY PUMP ASSEMBLY |
Measure the resistance of the suction control valve terminals.
- Standard resistance:
Condition
Specified Condition
20°C (68°F)
1.9 to 2.3 Ω
|
|
||||
| OK | ||
| ||
